Model #330 POULAN Chainsaw, Gas

  • Fan Housing/crankshaft/rod
    3 Results
  • Cylinder Shield/rod/wire Choke
    3 Results
  • Handle/clutch/chain/bar
    3 Results
  • Carburetor 530069895 Hda #164
    3 Results
Find part by diagram >

Question and Answers

Q:

samsung front loader and dryer set , the dryer wont dry.

A:

The dryer not heating can be an inconvenience and keep you from doing some laundry. I suggest you add to the thread of this question and include the full model number of your dryer so that the expert can provide you with a more detailed answer. I did manage to find a link that will provide you with some good information. I hope this helps with your dryer troubles while you wait for your expert response.

Read More
Joseph P. -
August 01, 2012
A:

The Samsung dryer will normally have a control board and a temperature sensor (also called a thermistor) to control the heat in the dryer. There are a number of problems that could prevent the dryer from heating. You could have a voltage supply problem. A bad sensor, a failed control board or a broken heating element could also prevent the dryer from heating.

I recommend that you check the house circuit breakers for the dryer first. Here is a brief video that describes that initial troubleshooting step: Video: Dryer Won't Heat . The dryer will run if it is getting the 120 volts of power from one leg of that circuit. If the second leg of power is missing, the dryer won't heat.

If the circuit breakers are okay, then I recommend that you check the voltage at the outlet as shown in this repair video: Video: How to Perform a Voltage Check on a 240 Volt Outlet . NOTE: You should only perform that live outlet voltage check if you are completely confident in your technical ability to safely complete that test. Follow the safety guidelines in that video when checking that outlet voltage .

If you only measure 120 volts at the outlet, then you will need to have an electrician repair that electrical outlet for the dryer.

If the voltage at the outlet is okay, then you will need to perform further diagnosis and troubleshooting on internal dryer components. Reply with additional details including the full model number of your dryer for more help with repairing this problem.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
August 03, 2012
A:

ok the model is dv330aew/xaa serial is yo9454bz902947k and it apears that the fuse box is fine, having problem finding the thermister

Read More
jd -
August 04, 2012
A:

Thanks for adding that model number JD. The first image below shows how to access the thermistor (temperator sensor). :You will need to UNPLUG the dryer and remove the front panel to access that component. You can test it from the control panel by using the information in the second image. That would involve less work. Check the resistance of the thermistor from that CN4 connection on the control board using a volt/ohm meter (with the dryer still UNPLUGGED). If you need more help, let us know.

Read More
Lyle W -
Sears Technician
August 06, 2012
A:

I have a DV330AEW/XAA front load dryer. The Heater control board and connector to the Heater relay burnt to a crisp. Connector on the wire harness and the relay are gone. What happened here. A bad connection? A short? Any other service issues with this product burning up these components that are of poor design? Any service recalls on this or simuliar issues of burnt components?

Read More
Chris Clark -
March 17, 2013
A:

Hello Mr. Clark. The failure that you are describing was likely caused by a short circuit to the cabinet ground in that heating system. I checked for recalls or common issues on that model of Samsung dryer. I did not find any recalls or common problems like the one that you are describing. Based on the type of failure that you experienced, I recommend that you have a service technician examine and repair the dryer. You can schedule service through this link: Sears Home Services Dryer Repair . If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
March 19, 2013
A:

Expert answers above reference a couple "images below" but nothing displays on website. Where can I find these images or other info on troubleshooting individual components?

Read More
Ron -
April 05, 2013
A:

Hello Ron. I suspect that you may be viewing the answer through the Sears PartsDirect website. The images are not being displayed on that website at this time. You can view the images by copying this URL and pasting it into your browser: http://www.managemylife.com/mmh/questions/311727-samsung-front-loader-dryer-set-dryer-wont-dry That will send you to the Manage My Life website where you can view the images. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
April 08, 2013
A:

Like Chris Clark above, my relay on the master board where the blue and black wires come in from the 240 also burnt (just the blue wire and relay where it attaches split. Replaced the board without any other changes... heat returned and after two months it happened again... So obviously another underlying problem like a short. I have seen several other complaint of this happening on Samsung dryers. Mine is a DV203AES/XAC built in 2007-11.

Read More
John -
July 31, 2014
A:

I have a dryer Samsung model dv330aewxaa03, the computer works and all buttons are, but when press the start button it does not work, nothing moves, I bought this dryer two years ago, does anybody have any idea of the problem

Read More
khalid nour -
December 28, 2014
See more answers
Q:

No Heat DV330AEW/XAA Samsung Dryer

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Julio -
April 05, 2013
A:

 Thank you for your question and I understand your concern.

The voltage supply must measure 220 volts when measuring across the two outer terminals of the terminal block where the power cord is connected or the dryer will not heat. I do not recommend measuring the voltage supply unless you have experience and feel safe and confident in doing so; otherwise I suggest calling a service technician to diagnose and repair your dryer. 

Each one of the components connected in a series circuit between the control board and heating element can be disconnected and tested for continuity with an Ohm meter. This will include the heating element, high limit thermostat and the thermal cut-off. The heating element must have a 220 volt power supply or it will not heat.  The line 2 (L2) voltage supply begins on the red wire at the terminal block on the back of the dryer where the power cord attaches. The line two (L2) voltage is supplied to one terminal of the heating element once the motor starts and the centrifugal switch closes contacts 1 and 2 which completes the (L2) voltage supply to one lead of the element at the red wire.

The line one (L1) voltage supply begins at the back of the dryer where the power cord is attached to the terminal block. The line one (L1) voltage is connected to the heater relay (RY6) with a black wire. The heater relay must close in order to complete the L1 voltage path to the (TH3) thermal cut-off (blue wire). The L1 voltage path is then routed to the Hi-limit thermostat from the thermal cut-off with a black wire. From the high limit thermostat, the wire changes to a blue wire which is routed and connected to the other terminal on the heating element. I added an image below of the wiring diagram toreference.

 

NOTE: I do not recommend measuring any voltage unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician to diagnose and repair your dryer. 

If the dryer is not getting 220 volts when measuring across the red and black wires at the terminal block where the power cord is attached, the dryer is not going to heat. The heating element must have 220 volts in order to heat. If the 3 thermostats measure continuity, and dryer is getting 220 volts, the control board is likely faulty.

I added a couple of images below to reference. 

 Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post.


Read More
Joey S -
Sears Technician
April 08, 2013
A:

I have no heat on my dryer I have confirmed I have 220 V on the black line feeding the heater relay but when I turn on the dryer and test the blue wire exiting the relay I do not get 220 V I have replaced the main control board and the display control board any help would be very appreciated

Read More
Chris -
October 26, 2015
See more answers
Q:

My dryer will start, it will heat, but the cycle will only last for 5 minutes or less. How can I fix this? DV330AEWXAA Samsung Dryer

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you. I can understand any frustration you may have experienced with regards to your unit. Let’s see what we can do for you.

It sounds like the issue would be with one of the thermostats. This could mean that there bad, or it could also mean that there is a blockage in the exhaust system you may want to try and clean out the whole unit front to back.

Hope this information has helped you. If you are not comfortable doing this repair you can click here to schedule a technician or call toll free 1-800-469-4663. Again, thank you for choosing SearsPartsDirect.com.

 

Read More
JeffwallaceIII -
Sears Technician
August 14, 2015

Top Parts