Model #316797210 CRAFTSMAN Blower, Gas

  • Engine
    3 Results
  • Housing And Accessories
    3 Results
Find part by diagram >

Question and Answers

Q:

replace fuel lines on leaf blower

A:

I'm sorry your having issues with your leaf blower. I would suggest that you provide a little more information such as the make and complete model number of your product so your expert will be able to provide you the best possible answer. Just click on reply below where you can provide the additional information.

Read More
Jackie S -
February 12, 2012
A:

model # 358798980 which port on primer goes to which port on carburetor. the carb has two ports, one a little smaller than the other does one of the lines go between the primer and in tank filter? provide schematic if possible. thanks

Read More
bruce -
February 12, 2012
A:

I am sending an image showing the routing of the fuel lines on most leaf blowers. If your blower is different than the image, reply on this thread and I will be glad to help.

Read More
Jimmy K -
Sears Technician
February 13, 2012
A:

Jimmy can you send me an image showing the routing of the fuel lines for my Craftsmand Blower. Model no. 316797210. Thanks.

Read More
james -
November 13, 2013
A:

This is exactly the same blower and question I had as the 2/12/12 post above (Craftsman 2 cycle gas blower model 358.798980). The diagram you provided above looks like it should answer the basic question, but it prints very small and fuzzy. Is it possible to send a larger, clear image? Also, I believe one line on the image provided is labeled "main fuel line", but I can't read the other line. What is it labeled? In my line kit I bought online, it has 2 lines. 1 line is a little larger than the other. Which line is the main fuel line and which size is for the other line (vent?)? The line kit also came with one vent fitting (from looking at the parts list and schematic, I believe that is what it is). Where does that go? As happened to the customer above, my lines were all crumbled and destroyed so there was no way of simply retracing how they were originally installed. But I found 2 vent fittings in the rubble. However, the line kit I bought only had 1 vent fitting. In any case I don't know their purpose or where to install them. Sorry this is a lot of questions, but please answer all of them. Thanks, Rock White

Read More
Rock -
September 26, 2014
A:

How do I get that vent fitting that goes into the tank connected with the new line on the ouyside?

Read More
clint -
July 13, 2015
See more answers
Q:

I would like to know the size of the different parts of the fuel line on my Craftsman blower 316.797210

A:

Thanks for the inquiry and for being a valued member.

The fuel line part number 791-181086 is 3/32 "x OD: 3/16 " x Length: 2 '. Unfortunately, the feed line part 791-182496 was not listed for an OD or ID spec, and I was unable to verify it. Typically the feed line is a smaller diameter than the return (791-181086). The fitting doesn’t need to be used. Most of the newer units don’t include or use the fitting any longer, so you can use a complete piece of fuel line rather than making use of it.

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
May 26, 2015
Q:

How do you replace fuel lines? 316797210 Craftsman Blower/vac

A:

Thanks for the inquiry and for using SearsPartsDirect.com.
 
The filter will attach to the end of the small fuel line. This line is the fuel pick up line. The other line is the vent line. To install the new fuel line you have to cut the end of the line at a severe angle. Push the angled end into the hole of the tank. Then reach into the fuel tank opening with a long pair of needle nose pliers and pull the fuel line into the tank. Once you have the correct amount in the tank cut the end of the fuel line square and install the fuel filter. The vent line only has to hang in the tank about a 1/2 inch. The fuel filter is connected to the end of the pick up line and sits in the bottom the fuel tank.
 
On the carburetor, the smaller fuel line with filter will connect to the tip on the carburetor that is curved (usually). The larger diameter line will connect to the other tip on the carburetor and go back to the tank as the return.
 
We do not have a model specific diagram for the fuel line routing, but I have posted an image below that may help:
 
 
Hopefully this helps and let us know if we can be of any further assistance. Thanks for using SearsPartsDirect.com.  

Read More
Jeff Wallace Sr -
Sears Technician
November 16, 2013