Model #315228510 CRAFTSMAN Saw Table

  • Craftsman Table Saw
    3 Results
  • Figure B
    3 Results
  • Figure C
    3 Results
  • Figure D
    3 Results
  • Figure E
    3 Results
  • Figure F
    3 Results
  • Figure G
    3 Results
  • Figure H
    3 Results
  • Figure I
    3 Results
Find part by diagram >

Question and Answers

Q:

Missing Rip Fence and Miter Gage. Please help 315228510 Craftsman Table saw

A:

Thanks for the inquiry and for being a valued member.

I am sorry to hear of the issue you're having getting the fence and the miter gage. I know how frustrating that is. 

Unfortunately, there have not been any substitutions made by the manufacturer for these parts. The fence shows as still in stock on the site, but I have seen instances where the part has in fact been discontinued. With no substitution made, we do not have a replacement to offer that would be a guaranteed fit. 

You can try Googling the part numbers to find new old stock, or you can look on Sears.com for some aftermarket replacements. 

We apologize for the inconvenience and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
January 07, 2015
Q:

Faulty Saw Arbor

A:

I understand how frustrating this can be. While you are waiting on an expert to answer your question, I suggest you visit your nearest Sears repair shop so they can fix this for you. I have attached the link below. Hope this helps!

Read More
Dezeray -
January 22, 2013
A:

I am sorry you are having this problem with the saw. In order to use different blades on the saw the arbor is threaded almost to the inter flange. I recommend checking the threads of the arbor. If the top of the threads are pointed, you may benefit by replacing the arbor. Originally, the manufacture used pointed threads that removed too much material and would cause this problem. If the threads are already flat on the top, a new arbor will not help. I have had other members tell me they wrapped to smaller section of the shaft with electrical tape. Doing that centered the blade and it would not move once the nut was installed. Another customer made a sleeve out of a .010 feeler gauge. He would put the sleeve on first. I have a Craftsman saw that was made by Emerson and have the same problem. What I found is the Excalibur dado blade worked the best. Please click here to see that blade. Thank you for using Manage my life.

Mark.

Read More
Mark T -
Sears Technician
January 23, 2013
A:

Thank you Mark. My issue is the threads on the arbor are of a smaller diameter than the inter flange. How do I get Sears to correct this issue. When I pay $600 (10 or 12 years ago) for a "Professional" model table saw, I expect it to perform basic table saw operations such as executing "Professional" dado cuts. I am not in the habit of jury rigging equipment to just get by. This is obviously a defect in the manufacture of the product. Thank you for any advise.

Read More
James -
January 26, 2013
A:

I have the new arbor. Can you give me detailed instructions on the best way to change the arbor. Thanks,

Read More
James -
November 01, 2013
See more answers
Q:

motor won't turn on tablesaw 315-228510

A:

Most likely the motor is indeed burnt out. You can check on the motor and make sure there isn't a capacitor that can be replaced as that would cause this type of problem, but the drawing does not show one as being used on this motor. If there isn't a capacitor on the motor then your best bet would be to find a local electric motor shop and have them check the motor out. If they cannot fix the motor or find a replacement, you may be out of luck as I do not show a replacement motor available for this model.

Thank you for using Manage My Life!

Read More
Wade_B -
Sears Technician
September 14, 2013

Top Parts