Model #3103 CRAFTSMAN Screwdriver Rachet

  • Unit Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

CANNOT FIGURE HOW TO REMOVE STOVE STORAGE DRAWER

A:

There is nothing more annoying than trying to remove a stubborn part. The experts here on Manage My Life will be able to assist you. It usually takes 24-48 hours to receive a response. Have a great day!

Read More
Jackie S -
July 25, 2011
A:

Thank you for your question and I understand your concern.

According to the model number provided it should release as follows. I also added an image below taken from the Owner's manual.

Getting the drawer to release can be tricky. You will need to slide the drawer open completely and pull the lever up with your finger on the left glide and push down on the lever with your finger on the right glide and slide it out of the glides.

Read More
Joey S -
Sears Technician
July 26, 2011
A:

Your image from the manual is so small that it is totally useless. Can't you provide one that is visible to people using a 15" laptop?

Read More
Ken -
August 20, 2013
A:

Ken: Without knowing the model number of your range, I will assume the model is 790.3103xxxx or 790.3104xxxx. Copy and paste the URL below in your browser to view the Owner's Manual. It will have the instructions for removing the warmer drawer. http://www.managemylife.com/mmh/lis_pdf/OWNM/L0809212.pdf

Read More
Joey S -
Sears Technician
August 21, 2013
See more answers
Q:

Gas Stove

A:

The Managemylife web site is a good resource of information to find out what may be happening and what options are available to you. I'm sorry to hear about the difficulties with your Kenmore range. I did some research at Managemylife website and found this expert answer to a similar question that may help until your expert can respond. I have attached the link below so you can check it out. I hope this helps.

Read More
James -
October 20, 2012
A:

It is likely that one of the burner switches got wet and is shorting out. Once the switch dries, it will probably stop ticking and will work normally. You can shut off the house circuit breaker for the range or unplug it to completely disconnect electrical power until the switch dries out. The igniters won't tick when the power is disconnected to the range. If you want to speed up the drying process, you can shut off the house circuit breaker to disconnect electrical power and open the console as shown in the image below. Your range will look slightly different than the one shown below but the basic procedure for opening that console is the same. Let the console air out for a day and then reassemble it. It is likely that the burner switches will work normally once they dry out.

If you continue to have problems with a burner switch, then reply with additional details and we will assist you further.

If you get to the point where you need to have a service technician examine and repair the range, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
October 22, 2012
See more answers
Q:

Why is baking not level? When I place two cake pans side by side, the cakes always bake thinner near each sidewall of the oven.

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina -
October 20, 2012
A:

Cakes that are not level is a common complaint. No matter the oven, there may be problems.

You can check to make sure the oven is level. I do not think that is the issue here, but the information to properly level the oven is in the image below. I think what is happening here is something called doming. When baking more than one cake at a time, they tend to rise on the sides next to each other and less on the side facing the wall. Baking strips may help as well as lighter colored pans. Another cause is gluten in the batter. Try switching to cake flour instead of all purpose flour or adding a bit more butter.

You indicated you are not using the convection option. If you do, remember to reduce the temperature by about 25 degrees. Also leave at least one to two inches between the pans and the oven walls and each other. Try baking on separate racks, then switch top and bottom about 20-25 minutes into baking.

Another tip that may help is cake pan strips. They help to insulate the sides of the pan to reduce the heat and prevent the sides overcooking too quickly. You can also wet the strips to help more. You can see an example of cake pan strips here; Sears .

I hope these tips help with the cake baking. Please reply if more information is needed. Thank you for using Manage My Life.

Read More
Barbara H. -
Sears Technician
October 21, 2012
See more answers