Model #29675 RCA VCR

  • No Image Available - Fidelitone
    3 Results
Find part by diagram >

Question and Answers

Q:

Pro Form Treadmill 831296750 Proform Treadmill

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Barbara -
April 27, 2013
A:

Hello Clinton. I posted a wiring diagram for that treadmill in the image below. That should help you replace the wires on the motor. If you need more assistance, let us know.

Read More
Lyle W -
Sears Technician
April 29, 2013
See more answers
Q:

Pro-Form Treadmill front roller/pulley - treadmill stops

A:

I can understand your concern when the roller pulley on the Proform treadmill is stripped and need replacing. An expert will research and respond on your specific question within two business days. If service is needed that link is provided.

Read More
Anna T -
January 29, 2013
A:

I know that it can be very difficult to have issues with your treadmill. Try this: Incline the treadmill all the way up. Then stand at the front of the walking area and give yourself a slight shove. You should slide back 75% of the way. If you do not go that far back then you will need to lubricate the walking belt. You can order kit number 219170 from HERE . If the belt does not seem to need lubrication it may be that the controller is failing. You can try putting the treadmill through the calibration mode to see if that can be corrected.

Press and hold the stop and speed "up" key while you insert the safety key. Once in the calibration mode press the stop button to get into level 2 of the calibration. Then press the speed up button and the belt should begin to move. It will go to top speed then slow back down to a stop. After the belt stops remove the safety key. Put the key back in and then try the treadmill to see if anything has changed. If the problem is still present then the controller will need to be replaced. I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
January 29, 2013
A:

Thanks for the response, appreciate the insight. The issue isn't the controller or the walking belt etc, it's the front roller and the pulley that attaches to the roller. They are two different peices although the manual says it's one part? The pulley and roller spin ok until you walk on the treadmill, then the pulley spins (as the moter and motor belt runs fine) but the front roller doesn't and makes a noise (like the the pulley insides are stripped?). The roller is metal and the pulley is hard plastic. (Rlr,drive,ar PART NUMBER: 235445)

Read More
Jim -
January 30, 2013
A:

Thank you for replying with this information. If the roller is not spinning when you apply pressure to the belt, then I would suspect that the pulley is malfuctioning. However, I would pull the pulley off of the treadmill and check it. If it is stripped, it will be visable. Please let me know if you need anything else. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
January 30, 2013
See more answers
Q:

Treadmill noise

A:

The treadmill making a strange noise can really cause some concern and I will be happy to help. I am adding two links below that will provide you with some good information to help you with your question while you wait for your expert response.

Read More
Joseph P. -
March 15, 2012
A:

The noise you hear may be the bearings in the roller. It could also be the motor belt starting to break or split. If you remove the motor hood you will be able to inspect the motor belt. If it looks good, take the motor belt off and walk on the treadmill to see if you still hear the noise. If you do, it will likely be the roller bearings.



Let me know what you find on this and we'll see if we can narrow it down further.



Thank you for using Manage My Life!

Read More
XX Wade_ -
Sears Technician
March 16, 2012
See more answers