Model #29650 CRAFTSMAN Pump

  • Shallow Well Set And Check Valve Assemblies
    3 Results
  • Motor Assembly
    3 Results
  • Check Valve And Venturi
    3 Results
  • Lower Flange
    3 Results
Find part by diagram >

Question and Answers

Q:

I have a sears radial arm saw, 113.29550 that the brake will not release and no parts manual, please help. I am in Costa Rica.

A:

ManageMyLfe.com is a great place to find your owner's manual and installation guides for appliances. I did some research and found the owner�s manual. I have attached the link below. Your expert will follow up and verify this information shortly. If you are having a specific problem please submit your question on the existing tread by click on the reply box below for your expert. I also found an expert answer that mau help.?

Read More
James -
February 07, 2012
A:

Thank you for your question on the brake for the radial arm saw.

I am not finding the model you have given me.

Please verify the model number.

Usually there is a screw on the right side top that secures a cover for the brake parts on the saw by the auxiliary motor shaft.

Some of the other models have a clam shell design and you will need to remove the blade guard and the saw blade and raise the arm and tip the bevel to expose the bottom of the saw to remove the recessed screws to split the clam shell covers.

Please let me know what you find and we can continue to troubleshoot with that information.

Sam A.

Read More
Sam A -
Sears Technician
February 07, 2012
A:

I have checked and the model number is either 113.29550 or 113.29650, the model number plate has a dent that partly obscures the first #5 or # 6 or not likely # 3. It is a 9" saw bought sometime in the early 70s by my wife who then work for Sears in Arkansas. I have removed the saw motor from the mounting and have turned it every way I can and see no recessed screws on the bottom of the motor housing. There is a post on this message board, http://www.samallen.com/wwwboard/messages/20104.html, that says he has a manual for the model number I have, 113.29550. Perhaps there is a way to get a copy of the parts pages from this person. I can also take digital photo of the motor housing if that would help. Thanks!

Read More
ArtEdwards65 -
February 10, 2012
A:

Thank you for the up date on the radial arm saw model number. I believe that it is a 113.29350 which is a 9" radial arm saw. It this is the model number then you are right in that this motor was not intended to be service by the customer. It was put together at the factory and needed to be repaired by a repair center that did motor repair at the Sears rebuild center. This service is no longer available. Take a look at the manual I have included in the link below to see if this matches your model. The replacement motor for this saw is obsolete and no longer available. I am sorry that I cannot help you with the repair of your motor. Sam A.

Read More
Sam A -
Sears Technician
February 13, 2012
A:

That appears to be the same as the saw I have. I have split the case, it is some kind of epoxy that holds the saw motor together. it is nothing but rush that is my problem. i mud dobber built it nest in the motor while it was in storage which drew moisture and caused the rust. No way of my knowing what epoxy they used so I'll just wing it when I put the motor back together. What a shame that there is no way to properly service this saw. Art

Read More
ArtEdwards65 -
February 13, 2012
A:

Thank you for the update. When they were rebuilding the motors at the Dallas rebuild center they had a jig that they put the motor into for holding it during the oven curing of the epoxy. It is critical that the rotor is located in the winding correctly or it will scrub the fields and fail. Best of luck in getting this motor repaired. Sam A.

Read More
Sam A -
Sears Technician
February 14, 2012
See more answers
Q:

More water from craftman pump

A:

I'm very sorry to hear that you are having such a problem getting the answer you need. For this type of problem you should consult a plumber. The expert will respond to your question within 24-48 hours.

Read More
aashe -
June 13, 2011
A:

Thank you for your question.

I apologize that you have not received the information you need to correct you water well issue.

Since you have replaced the old pump with a new one and you still have the same results tells me you have a problem with the mechanics of the delivery pipes.

Have you check to see if your foot valve at the bottom of the well is opening freely to open wide enough to get a good water volume through.

It sounds like it is restricting the water to about 5 gallons per minute.

I going to assume that you have adjusted the water volume control on the pump housing to make sure it�s at maximum output.

With out the model number of the pump I cannot verify that you have the correct venturi nozzle or venturi for the motor pump housing.

I have included a screen shot of the nozzle and jet packs that came up with the 29650 number.

I hope this was of some help. Please reply with the model number of your pump if you need more assistance.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
June 15, 2011
A:

Sam I have a 1hp convertible hydro glass craftman water pump mfg. by AO Smith mfg.#2522 sears mod #08302522000 with the mfg# 29650 craftman mod # 29329650000 shallow well jet package attached for shallow well. I am sorry I left all this out when I last contacted you but I was having problems and I forgot. Now with all that out of the way the check valve is in the shallow well package attached to the pump, and on the old pump the valve was above ground so thats 2 different check valves and the pressure is set to cut off at about 70psi. When I purchased the shallow well package there was only one venturis included and the instructions said something about max water use venturiXX and I do not remember the part # and of course I lost the instructions.Oh when you say foot valve I hope you mean ck valve. If I run two sprinklers neither have enough water to work properly. I received your parts list thanks and I think I have the part #s. Let me know what you think and if all this makes sense. Thanks Jimmie

Read More
jimmie -
June 17, 2011
A:

Thank you for the update. This being a shallow well pump system the jet package is on the front of the pump housing with the check valve in front of the venturi. Some well systems have a check valve at the bottom of the pipe in the well. If you did not install it you would have to pull the pipe to know it you have a check (foot) valve at the bottom of the pipe in the well. Did you notice that there is a volume control on the pump housing and looks like a large nut with a slotted screw in the center? The venturi has to match the pump and I think that you have the correct ventri is the parts list for the pump and jet pack match. Let met know any more information that is would be helpful. Sam A.

Read More
Sam A -
Sears Technician
June 20, 2011
A:

Sam I have located the volume control on my pump now I need to know how to adjust it and what should be the results. I washed my well down my self and prefer to have the check valve at the pump rather than at the bottom of the well pipe where like you said you would have to pull the pipe out of the ground if there was a problem. I had another pump at the lake where pvc pipe was used and I had a pvc dresser couplin at the pump to make it easy to disconnect and winterize with the check valve at the bottom of the well pipe. Would you believe if I left pressure on the system the well pipe would seperate at the couplin? I installed a brass check valve and that corrected the problem. Please let me know how to adjust the volume control. Thanks again Jimmie

Read More
jimmie -
June 20, 2011
A:

Thank you for the update. Turn the screw counter clockwise to make the water flow port larger. It is not a large difference that you can tell, but it will increase the volume of water to a point. Sam A.

Read More
Sam A -
Sears Technician
June 21, 2011
See more answers
Q:

Can this deep well pump be converted to a shallow well pump

A:

When it comes to doing a repair or installation it can definitely be a challenge, I can understand how important it is to get the instructions or information to do it right. To help you I have attached a link below that has useful information for you. Hope this is helpful!

Read More
Maira E -
October 19, 2010
A:

You will need jet pack number DP29650 to do the conversion on your pump. The kit will come with installation instructions. You can order the kit HERE if you'd like.

If you have any further questions, please let us know.

Thank you for using Manage My Life!

Read More
XX Wade_ -
Sears Technician
October 20, 2010
See more answers

Top Parts