Model #2917 AMANA Free Standing, Gas

  • Backguard Assembly
    3 Results
  • Top/burner/spark Ignition
    3 Results
  • Top/burner/spark Ignition Page 2
    3 Results
  • Griddle Top/burner
    3 Results
  • Griddle Top/burner Page 2
    3 Results
  • Lower Oven Components
    3 Results
  • 20"/24"/30" Cabinet Assemblies
    3 Results
  • 20"/24"/30" Cabinet Assemblies Page 2
    3 Results
  • Cabinet Assembly/griddle
    3 Results
  • Cabinet Assembly/griddle Page 2
    3 Results
  • Oven Door
    3 Results
  • Lower Broiler Components
    3 Results
  • Broiler Door/accessories
    3 Results
Find part by diagram >

Question and Answers

Q:

What do I need to adapt this to also be used as a drill press?

A:

I see you need to adapt to also be used as a drill press. While you are waiting on an expert to answer your question. You can visit SearsPartsDirect.com website to order parts. I attached the link below. Hope this helps! Good luck.

Read More
Dezeray S -
September 08, 2010
A:

I appreciate your help, but until I know the part(s) I need, I can't order them.

Read More
Davella -
September 08, 2010
A:

There isn’t a way to turn your radial arm saw into a drill press. I won’t sit and say there isn’t a brand out there that you can do it on, but I do know that you cannot do it with yours. I searched the web using Google and unable to come up with anything. I did find lots of information on a radial arm drill press. But that is not the same idea. A radial arm drill press is basically a (usually) very large drill press that has a very mobile drilling head (left, right, up, down, forwards, backwards, etc…). I’ve used one before (about the size of a pickup truck) and the movement idea is the same as with a radial arm saw, but that’s where the similarities end.

Thank you for using Manage My Life!

Read More
XX Wade_ -
Sears Technician
September 08, 2010
A:

Well, I don't know XX Wade _EXPERT, has ever tried it of not, but you can turn your 10" Radial Arm Saw into a drill press and a router, just by removing the blade, and putting a 1/2" chuck in it's place, then rotating the head down, then you insert a drill bit, and run the arm up or down to drill! It is not as good as a drill press, but it will work! You can put a router bit in the chuck and route wood too! I have routed the edges of two big book cases, and the shelves, and routed a big head board that I made for my queen size bed, with my radial arm saw and a router blade. I wouldn't try to drill anything but wood, but wood does fine! You just need to make sure that your piece that you are drilling, is clamped down real good. You don't want it to come loose and sling around and hit you!

Read More
Roy -
May 12, 2015
A:

One more thing, you can also get a POWER TOOL KNOW HOW book, #9 2917, from SEARS on the RADIAL ARM SAW, BAND SAW, DRILL PRESS, WOOD LATHE, WOOD SHAPER, STATIONARY PLANERS, STATIONARY SANDERS, AND WOODWORKING TECHNIQUES! In Chapter 6, page 62, it shows you how to attach a 1/2" chuck to the accessory shaft end of your radial arm saw. And shows you how you can drill, route, and carve, with your radial arm saw!

Read More
Roy -
May 12, 2015
See more answers
Q:

How do I get a manual for Sears Captive Air water tank model 390.291701. When I look up that model it shows a sump pump!

A:

I know how important it is to have the owners manual for most home appliances so that you can troubleshoot properly. While you are waiting for your expert answer, I did manage to find a link that will provide you with some information to help you find the correct model number of your appliance. I hope my link is useful.

Read More
Joseph P. -
May 24, 2011
A:

Thank you for your question.

I can understand wanting to have the owner's manual for the captive air tank.

I have found the manual for the 390.2917series manual for all that series if the same 642-9301 manual.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
May 25, 2011
See more answers