Model #28044 FRIGIDAIRE Free Standing, Gas

  • Gas Range/ Front Cover
    3 Results
  • Backguard
    3 Results
  • Backguard Page 2
    3 Results
  • Burner
    3 Results
  • Burner Page 2
    3 Results
  • Body
    3 Results
  • Body Page 2
    3 Results
  • Top/drawer
    3 Results
  • Top/drawer Page 2
    3 Results
  • Door
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

How to change the tension on a pro-action whirlwind bike model number 831-28044.2?

A:

There is no tension adjustment on this model exercise bike. The fan on the front wheel provides the resistance as you pedal. The resistance stays the same throughout the exercise program.

Read More
Jimmy K -
Sears Technician
February 20, 2009
A:

thanks much.

Read More
Maria Buonopane -
February 25, 2012
See more answers
Q:

Left handlebar not completing its full revolution after install of new bearings.

A:

Having an exorcizing bike in the home is very beneficial to say the least. I have read and understood the issue that you are having with the handle bars of the bike. I was unable to find a similar issue on this site but the good thing was that i was able to find the Owner's Manual. I hope that it helps you understand it a little bit more.

Read More
celene -
April 07, 2011
A:

I am assuming you replaced the crank bearings.

It sounds like a bushing has failed inside the handlebar. Remove the left handlebar from the shaft and inspect the shaft and bushings. You might need to clean and lubricate the bushings. If so, use silicone grease.

It is probably a coincidence the bushings in the handlebar chose this time to act up.

Read More
Jimmy K -
Sears Technician
April 08, 2011
See more answers
Q:

excercise bike noise

A:

You can find this kind of troubleshooting information is your owners manual. If you do not have yours, a handy thing about the Manage My Life website, is you can go onto the top of the Manage My Life website and click on the tab button then insert your model number into the search box. I have attached a link below so you can view. I hope the link that I have provided you is useful.

Read More
Alina F. -
December 09, 2010
A:

The problem you're describing sounds like the bearings. Where the crank is, there are bearings and a flywheel. When those bearings start to go out, there will usually either be sounds or a grinding feeling when you pedal. After some time it will get to where it becomes hard to pedal.

You will need to replace the bearings on the crank assembly to fix this problem. If you've not ever done that sort of thing on bicycle or exercise bike, it's not something I recommend you try to do. It's not a super hard job, but it is one where you kind of need to know what you're doing so you don't have to keep taking it back apart.

If you're up to try it, you can go HERE with your model number and look at the parts pictures. You can also order the bearing sets (takes 2) at the same site, part number 176991.

If you would rather have a tech come out and take care of it, you can arrange for that here: Sears Home Services .

Thank you for using Manage My Life!

Read More
XX Wade_ -
Sears Technician
December 10, 2010
A:

thanks for the suggestion..:) about how much does it run to have a tech fix it? i cant get an answerfor that..am just looking for an idea on repair cost before i have them come out and then find it costs like 200 dollars!!

Read More
dana -
December 10, 2010
A:

Just the parts for that would cost around $40-$50 (for both sets). Labor, would likely be around $100-$150. You may want to try and make the repair yourself. It certainly won't hurt anything. You just may have to take it back apart a time or two to get everything tightened correctly.

Read More
XX Wade_ -
Sears Technician
December 10, 2010
See more answers