Model #25377132790 KENMORE Top-Mount Refrigerator

  • Doors
    3 Results
  • Cabinet Parts
    3 Results
  • Shelves And Accessories
    3 Results
  • Unit Parts
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

How to replace an ice maker thermostat assembly?

A:

I understand that you want to replace the ice maker thermostat on your refrigerator. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina -
March 15, 2013
A:

Thank you for your question. Replacing some parts can be a challenge sometimes. The thermostat (# 21 in image) in this model is located in the control housing (# 17). First, disconnect the power and then you can remove the screws holding the control housing. Now, lower the housing and you will have access to the thermostat. Remove the screws holding the thermostat and pay close attention to how the sensor on the original thermostat is installed and install the sensor on the new thermostat the same way. I hope this will help you. If you would like more assistance, reply to this thread and I will assist you further.

Read More
Scott D -
Sears Technician
March 18, 2013
See more answers
Q:

What are the specs for Kenmore top mount refrigerator?

A:

Knowing the information about an appliance can be helpful if buying,selling or comparison shopping. By specs I think you mean cubic feet. I attached a link below that will help you find that information. This might provide some of what you are looking for while you wait for the expert.

Read More
Barbara H. -
June 17, 2011
A:

Due to the age of the unit, the only information available to us is the cubic feet of the unit which is 18.2 cu. ft. I hope this helps.

Read More
Korinna S -
Sears Technician
June 18, 2011
See more answers
Q:

How do i shut off a built in ice maker in a kenmore refrigerator?

A:

I know how important it is to have a good working ice maker in the home and I will be happy to help. While you are waiting for your expert answer, I did manage to find a link that will provide you with some good tips. I hope my link is useful.

Read More
Joseph P. -
May 14, 2011
A:

I'm sorry you're having a problem with this icemaker. The information you have received from Joseph is good but it does not pertain to this problem. This icemaker has a bail arm (# 22 in first picture) that moves up and down when the icemaker cycles. To turn this icemaker off, lift this arm up until it locks in place (see second picture). I hope this will help you. If you would like more assistance, any additional details will be helpful and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
May 16, 2011
A:

Hi Scot: Thanks for your input .I am familar with this Bail arm it is used to turn off the ice maker when the ice bucket is full provided the refrigerator is connected to a cold water source. My problem was the whole Ice Maker made too much noise at random times. After unplugging the wiring harness that stopped one loud noise.Then I heard the ice maker rotating inside the freezer.I opened the door and watched it rotating.I then flipped up the Bail arm in the middle of a rotation, But the Bail arm did not stop the rotation. The bail arm is now flipped up and so far I have not heard any unusual noise.I'm keeping my fingers crossed. Anyway the noise reduction now is great. The refrigerator is a good unit and now seems to run smoother. Thanks for your advise

Read More
Richard -
May 16, 2011
A:

It appears you have solved your problem. Just so you will know, if the icemaker is already in a harvest cycle, raising the bail arm will not stop it. The icemaker will continue through the cycle but will not start a new cycle again, unless the arm is pulled down. Thank you for using Manage My Life.

Read More
Scott D -
Sears Technician
May 17, 2011
See more answers

Top Parts