Model #25353322303 KENMORE Side-by-Side Refrigerator

  • Freezer Door
    3 Results
  • Refrigerator Door
    3 Results
  • Cabinet
    3 Results
  • Shelves
    3 Results
  • Controls
    3 Results
  • System
    3 Results
  • Dispenser
    3 Results
  • Ice Container
    3 Results
  • Ice Maker
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

My evaporator fan is turning on and off constantly, every 5 or 10 seconds 25353322303 Kenmore Refrigerator

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your refrigerator and I do understand your frustration. Glad to help out. I'm looking at your model number 25353322303 and from your description I would suspect an issue with the fan motor. Here is a link for a video that may help testing the fan. If you have a multimeter and know how to test the power being sent to the motor that may also help determine if the board is the issue or the motor. I do not recommend attempting any testing if you do not feel comfortable or do not know how to. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
January 27, 2015
Q:

Why does the filter on my Kenmore refrigerator shoot out?

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Alina -
June 06, 2013
A:

Thanks for trying to help. Anytime the water is used, the filter shoots out. This is true of the water dispenser and the icemaker, almost as if the water hose is not fully sealing to the back of the filter. I look forward to a solution. Thanks again!

Read More
Matthew -
June 06, 2013
A:

Thank you for your question.  I am sorry you are having a problem with your new Kenmore 253.53322303 refrigerator.  The image below contains the instructions for installing the filter.  Do you feel the filter snap into place?  Is the filter flush with the front of the housing?  There has been no history of this type of failure. 

The ice maker problem may be related.  Is there any water in the ice maker mold?  Try giving the filter an extra push to snap into place and let me know if that helps. 

You can reply below with any additional details for further assistance. 

Read More
Fred M -
Sears Technician
June 08, 2013
A:

Hi Fred: Thanks for your information. The filter does feel flush against the front of the housing, but the filter does not actually "snap" into place. I have pushed it as far as I can make it go, but it does not sound like it is snapping correctly. I see two small screws on the bottom of the housing. Am I supposed to tighten those? And to answer your question about the icemaker: whenever the icemaker tries to activate and fill with water, the filter shoots out. Thanks for your help!

Read More
Matthew -
June 08, 2013
A:

Matthew. The screws being tight should not make a difference. From the description of the problem I suspect the housing is the problem and not the filter. You will need to remove the two screws to remove the housing.

Read More
Fred M -
Sears Technician
June 11, 2013
A:

Thanks, Fred. There are more than two screws. I didn't notice it before, but that housing also has the facing for the thermostatic control knobs and it also lines the left side of the ceiling of the fridge. I tried to take pictures but my camera won't cooperate. From what you're telling me, I probably need to replace that large housing, correct?

Read More
Matthew -
June 11, 2013
A:

Believe it or not, I think i have it fixed. I pulled the filter out and then jammed it in. No problems since yesterday. Thanks for your help!

Read More
Matthew -
June 12, 2013
A:

Good job.

Read More
Fred M -
Sears Technician
June 15, 2013
A:

This is a known issue with the clamping mechanism that holds the filter in place (as I was informed by the Sears technician who addressed this problem via an on-site service call covered by my extended protection coverage; the clamps are integral to Item # 139, "Refrigerator Water Filter Base", on the "Controls" parts diagram). Simply "crimping" the metal clamps that hold the corresponding projections of the filter - an action readily effected by hand - has always sufficed to restore the clamping ability of the mechanism and prevent the filter from being forced out by the water presure. It would appear this occurs when a filter is removed for changing, even if some care is exercised in removing it via the provided "filter eject" button (Item # 138, "Filter Button", on the "Controls" parts diagram); I routinely just "re-crimp" the two metal "clamps" in the afore-mentioned base ass'y every six months when I change the filter.

Read More
Jones -
May 28, 2014
See more answers
Q:

Ice Maker Trouble Shooting Guide

A:

Good morning... I can fully understand your concern regarding this issue. I did locate a link that will discuss this situation in greater detail. Though this link discusses a different model number, the mechanics are likely going to be very similar. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will help guide you as to what might be wrong with your ice maker and have a nice day.

Read More
Henry -
February 01, 2013
A:

Thanks for the question about your ice maker; sorry you are experiencing a problem with ice production.

I have attached an image below that shows how to test the ice maker I believe you have. You will need to remove the head cover to see the module of the ice maker. (The part number you provided does not bring any data at all) so I researched and found the replacement ice maker and the image is for that ice maker.

Always disconnect power supply before servicing the appliance and when testing live voltage be sure to wear proper safety equipment (gloves and eye protection) also be aware of sharp metals on product



Based on your description of the problem, there will either be a bad inlet valve or internal ice maker components and the ice maker will need replacing. All this considering that your freezer is maintaining a temperature of 5 degrees or less, which is what it takes for the ice maker to cycle and produce ice.
I hope this helps, if you need additional assistance please reply with more details and I will be happy to respond.

Ron H.
If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Ron H -
Sears Technician
February 02, 2013
A:

Here is the imaged again.
Ron H.

Read More
Ron H -
Sears Technician
February 02, 2013
See more answers

Top Parts