Model #25344354401 KENMORE Side-by-Side Refrigerator

  • Freezer Door
    3 Results
  • Refrigerator Door
    3 Results
  • Cabinet
    3 Results
  • Shelves
    3 Results
  • Controls
    3 Results
  • System
    3 Results
  • Ice & Water Dispenser
    3 Results
  • Ice Container
    3 Results
  • Ice Maker
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Why does my model 253.44354401 refrigerator and GCD-23 icemaker allow water to drip over the cubes and run into the tray and then out the door dispenser?

A:

From the description you give I suspect there are two potential causes of this problem.

The water fill to the icemaker is a timed fill which the icemaker controls.

You say the water drips onto the cubes and if you mean the water never shuts off and continues to trickle in then that would most likely be an water inlet valve problem.

If the water overfills the icemaker but will shut completely off then there is an adjustment you can try on the icemaker.

To make further checks you will need to remove the icemaker so the front cover can be removed.

With the cover off the icemaker there is an adjustment screw with (+) and (-) markings. You can use a screwdriver to adjust the fill. If the icemaker is overfilling then turn the screw towards the (-) sign to decrease the fill time. It's best to make one turn then check the fill and adjust as needed. Usually only a 1/2 turn or a full turn is all that is needed.

I hope this information is helpful to you but you can submit another question with any additional details for further assistance.

Read More
Fred M -
Sears Technician
March 13, 2010
A:

My GCD-23 icemaker routinely does not kick out all of the ice. There's always one piece that is stuck there, keeping the blades from rotating on around and thus keeping the unit from filling up again. I always have to go in there and flip out that one piece of ice. Any suggestions? The filter is only about one month old, and I rarely get water from the water dispenser.

Read More
Terry -
July 16, 2012
See more answers
Q:

How does the kick plate attach on my refrigerator?

A:

The water line should pass through the hinge as in the pictorial attached. Then the kick plate should clip in place.

To Install Toe Grille

1. Open freezer and fresh food compartment doors.

2. Line up toe grille at base of refrigerator, making sure the four bottom tabs are resting through holes at base of cabinet.

3. Starting from left side of toe grille, press in on first top tab using your thumb and push toe grille forward until it snaps in place. Continue this process until all tabs are snapped in place and toe grille is secured to refrigerator.

Read More
Plumbing Bucket -
Sears Technician
May 02, 2008
A:

This is a dishwasher, not refridgerator

Read More
Anonymous -
March 12, 2011
See more answers
Q:

my kenmore model 253.44354401 side by side refrigerator will not make ice. There water supply and the switch is on.

A:

A ice maker is a important feature on a refrigerator, to help you I have attached a link below to manage my life where a expert answered a similar question that can be very helpful to you. I hope it helps! http://www.managemylife.com/mmh/questions/118791-kenmore-refrigerator-making-ice-1 http://www.managemylife.com/mmh/questions/119574-kenmore-refrigerator-making-ice-2

Read More
Maira E -
October 28, 2010
A:

After further online reading I found that ice will not be made unless it is 17 deg. or less in the freezer. I changed the setting from 8 to 9 (the highest) and this morning I had ice.

Read More
mschluth -
October 29, 2010
A:

Thank you for your question.

The ice maker not producing ice and be inconvenient.

I understand your details you said it just quit working after you cleaned it the first time. And then it started again.

My question is it not delivering ice or not making ice? If the ice bin is full then it would be an ice dispenser problem.

� From the symptoms you are giving me, I think you may need to turn the freezer control up one number to get the ice maker to harvest more consistently. It requires 0-6 degrees for the ice maker to enter the harvest cycle and it sounds like it may be right on the edge temperature wise.

� This would be especially true it there is ice in the ice maker mold for a long period of time. It should harvest about every 2-3 hours until the bin is full.

I hope this will help with your ice maker problem.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
October 30, 2010
See more answers

Top Parts