Model #25323429100 KENMORE Upright Freezer

  • Door
    3 Results
  • Cabinet
    3 Results
  • System
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Why does ice build up on the floor of my Kenmore 253.23429100 freezer?

A:

This type of problem is usually the result of a frozen drain. Every time it goes into a defrost cycle, the water will back up into the freezer, instead of going down the drain. The back panel in the freezer will have to be removed to access the drain and clear it. Before removing the panel, be sure to disconnect the power from the unit. The panel is held in place with some screws and when removed, the panel will pull out. You can clean the drain with hot water. Make sure the water runs all the way through the drain to the bottom pan. If you don't feel comfortable performing this procedure, call to have a technician clean it out. If you need more assistance, you can resubmit your question with more details.

Read More
Scott D -
Sears Technician
September 03, 2009
A:

I was trying already to open the back panel in the freezer. Was not able to do this as it seems to be held in place not only by screws. How can I get drawings with the relevant parts shown? Service manual? Thanks

Read More
Mark -
August 09, 2012
See more answers
Q:

kenmore freeze how to remove shelf #216546200 and replace #216204900 gasket,evap cover.

A:

I'm sorry to hear that you are having some difficulties with your freezer . I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assist you.

Read More
Barbara H. -
November 04, 2011
A:

Thank you for your question. The information you have received from Barbara pertaining to the evaporator cover is correct. The shelf fits in holes on both sides. To remove it, slide the shelf all the way to one side and then lift the opposite side from the wall. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
November 05, 2011
See more answers
Q:

how to install #216204900 gasket,evap cover and #216522306 gasket,door seal. kenmore freezer model #253.23429100

A:

A Refrigerator is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Priscilla V -
October 31, 2011
A:

To install the evaporator cover gasket disconnect the power to the freezer and remove the food, baskets, and shelves from the freezer. Remove the screws in the evaporator cover and remove the evaporator cover. Install the gaskets on each side of the evaporator cover. The gaskets are formed to slide over the sides of the evaporator cover. Install the evaporator cover and put the shelves, baskets, and food back in the freezer.

To install the door gasket, you need to remove the freezer door from the cabinet. Put the new gasket into a bathtub in warm water for 20-30 minutes while you remove the freezer door. Remove the screws holding the lower hinge to the cabinet and remove the door. Disconnect power to the freezer while replacing the gasket to prevent the evaporator coil from frosting up while the door is off. You can cover the food inside the freezer with quilts or blankets while the door is off.

Lay the door handle down on a padded surface and remove all the screws holding the door inner liner and gasket to the inside of the freezer door. Place the door flat on the surface with the door handle hanging over an edge.

Place the new gasket on the inner door liner with the holes in the gasket lining up with the holes in the inner door liner.

Start all the screws but don't tighten them. Mount the door on the cabinet and align the door so the gasket seals all the way around. Open the door and hold the door with one hand behind the screw you are tightening to keep the door aligned. Tighten a few of the screws and close the door to check alignment as you go around the door.

Read More
Jimmy K -
Sears Technician
November 01, 2011
See more answers

Top Parts