Model #25316082108 KENMORE ELITE Chest Freezer

  • Door
    3 Results
  • Cabinet
    3 Results
  • System
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore Elite Chest Freezer - Disable Alarm

A:

I understand that you want to disable the alarm on your Kenmore Elite chest freezer. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina -
August 30, 2012
A:

Thank you for your question. The alarm is built into the control and there is no cable or plug to disconnect. The only way to disable it is, to press the alarm off key pad. Now, it can also beep if the battery is weak or gets disconnected. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
August 30, 2012
A:

Is there a way to access the OCP board in the lid of the freezer without breaking the plastic rivets that appear to hold the lid, lid seal and lid interior liner together?

Read More
Lauren -
August 30, 2012
A:

Lauren, the overlay (# 57 in image) has to be peeled off to access the control. Now, the overlay can and usually does get damaged when this is done and a new overlay # 216947402 will probably be needed.

Read More
Scott D -
Sears Technician
August 31, 2012
A:

Yes, I have peeled back the overlay, but still cannot directly access the control board. How is the handle retained? Are there clips, snaps or screws that hold the handle onto the outside of the freezer lid?

Read More
Anonymous -
September 04, 2012
A:

To remove the handle in some models will require separating the inner and outer door panels. I recommend removing the door and laying it down to separate the panels. Again, with some models the control can be access, by removing the overlay and in others, the panels will need to be separated. It would be very unlikely that the display control board would need to be replaced. The main control board controls all the functions. I hope this will help you.

Read More
Scott D -
Sears Technician
September 05, 2012
A:

It looks like the door panels (and door gasket) are held together with "plastic rivets". Are these retainers able to be removed and re-used, or would they need to be replaced due to breakage upon removal? Any advice on how to remove these rivets without breaking them? Thank You!

Read More
Lauren -
September 10, 2012
A:

Lauren, the rivets would have to be drilled out and I would recommend having a techinician do this. However, this control will have no effect on the alarm.

Read More
Scott D -
Sears Technician
September 11, 2012
A:

Okay. You are telling me that all the sensors and controls for the audible alarm are not located on the display/control board in the handle on the door. The actual "beeper" is located on the display/control board in the handle. I was thinking about disconnecting the beeper on this board (cutting an etch on the PCB or breaking the beeper), but drilling out the plastic rivets does seem a bit destructive. Especially if I don't have the replacement rivets or the tools to install them correctly. So, the Main Control Board is what drives the audible alarm. There must be a cable that connects the Main board to the Display/Control board. Also, there must at least one wire in that cable that is dedicated to the audible alarm. PLEASE help me identify the location of the wire(s), or pin numbers on a cable connector, that provide power to the beeper. Thanks!

Read More
Lauren -
September 18, 2012
A:

Lauren, there are no wires or cables that can be disabled for the alarm. The alarm is built into the main module that is located next to the compressor. This is a safety feature and the only way to silence the alarm will be to press the alarm off button and then only the light will continue to flash. If the alarm still sounds and the temperature is ok, the module will probably need to be replaced.

Read More
Scott D -
Sears Technician
September 19, 2012
See more answers
Q:

My electronic control board (the one on the handle that says they temp) went out on my chest freezer and I ordered a new one. How do I install it? 253.16082108

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your freezer. Upon researching model253.16082108; to remove the control board once the overlay is off there are 2 screws in a deep hole that need to be removed in order for the control board to be removed. I have posted a link of the diagram that shows the screws that need to be removed.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
March 09, 2015
A:

I have the same issue, but my freezer handle doesn't have two screws in a deep. I Only have two deep holes. Please advise.

Read More
David -
June 22, 2015
A:

I believe the newer model is a snap on.

Read More
David -
June 22, 2015
See more answers
Q:

electronic temperature control 25316082108 Kenmore Elite Freezer

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your freezer. Upon researching model25316082108; The "CE" error code is a communications error; the low voltage board and high voltage board are not communicating. Check for poor wiring connections between the boards, check for any pins backed out of wiring connectors, check for broken/open wiring inside the door.

The High voltage board is located where the compressor is located; the low voltage board is located in the handle/display board area.

I trust this information will help you, we appreciate your business thank for choosing Sears.

 

Read More
CarlosZ -
Sears Technician
April 13, 2015

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show