Model #25000 SEARS Soccer Table

  • Unit Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Battery removal on craftsman rider 247.25000.

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner. Have a great day!

Read More
Alina -
August 07, 2012
A:

Thank you for your question.



I am sorry you are having a problem with the mower. I will be happy to assist you. Accessing the battery in this model is different from most mowers. To access the batter you have to remove the seat first. Then remove the knobs on the levers that go through the fender. Next, remove the two screws in the rear cover. The first image below shows how to remove the seat and cover. Click on the image to enlarge it. After you have theses removed, take the screws out that secure the fender to the mower. It should have 4 to 6 screws located under where the seat would be. Then lift the fender off the mower. The battery is on the left side. Just remove the cables and the battery hold down. Then lift the battery out of the mower. To install the new battery just reverse these steps.

I hope this is helpful. Please let me know if you need further assistance.



Thank you for using Manage my life. Mark.

Read More
Mark T -
Sears Technician
August 08, 2012
A:

thanks for everyone's help

Read More
Robert -
June 02, 2013
A:

Robert, I am glad the information was helpful. Please let us know if you need further assistance. Thank you for using Manage my life. Mark

Read More
Mark T -
Sears Technician
June 05, 2013
A:

Will you please post larger pictures of the diagram for battery removal. I am a 69 yr. old woman and am doing this myself. I have saved the printed words but, can not see the pictures posted above by the expert, Mark

Read More
Catharine -
January 29, 2016
See more answers
Q:

Blinking LED lights 10651133210 Kenmore Refrigerator

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your refrigerator. Upon researching model 10651133210:  you can unplug the refrigerator power cord for 5 minutes and then reapply the power to reset the unit controls. If the problem persists then the dispenser control board may need to be replaced, when the dispenser control board fails it can cause the controls for the dispenser to become unresponsive. I have posted a link of the dispenser control board#8 on the diagram linked, to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
July 09, 2015
A:

I have the same problem, the fridge is roughly 2 years old as well, so I followed your advice. First I unplugged it for 5 minutes and the problem still persisted. Then I bought the control board you described and replaced the old one and the lights are still flickering. Can anyone here help with the right answer please?

Read More
Mike -
October 21, 2015
A:

I feel you, Mike. Ours is still broken. I did not go as far as you and replace the control board. But unplugging-plugging back in did nothing. So, we put tape over the switches to make the blinking lights stop (my "disco fridge" was giving me a headache...) and now we deal with a dark fridge/freezer. Ticks me off this POS is less than 2 years old! If this many people are having the same problem, I fee like Sears/Kenmore should do something about it! I cannot afford to pay a tech $250+ to come out and fix this... So I'm stuck with no lights and waiting until something else breaks!

Read More
GREGORY -
October 22, 2015
A:

I feel you, Mike. Ours is still broken. I did not go as far as you and replace the control board. But unplugging-plugging back in did nothing. So, we put tape over the switches to make the blinking lights stop (my "disco fridge" was giving me a headache...) and now we deal with a dark fridge/freezer. Ticks me off this POS is less than 2 years old! If this many people are having the same problem, I fee like Sears/Kenmore should do something about it! I cannot afford to pay a tech $250+ to come out and fix this... So I'm stuck with no lights and waiting until something else breaks!

Read More
GREGORY -
October 22, 2015
A:

We purchased a complete set of Kenmore appliances for our new home (including this refrigerator) last year end of August. The appliances were not delivered or installed until the end of November. About 6 months into use, the washing machine developed to small leak around the door gasket (while in warranty), but unfortunately did not call the problem in until two weeks out of warranty. Since that time, the low speed blower setting on the microwave vent has malfunctioned (blower stays on high for both high and low settings), and last week, our refrigerator began the "dsco" light strobing in both freezer and refrigerator . Like others, for the LED light issue, I attempted the 5 minute reset without the problem being resolved. Now the question is do we spend the money to replace a board, that like Mike's experience, may not resolve the issue. It seems to me that there can only be three potential issues: 1. the LEDs themselves (unlikely I believe), the switch, or a control board / driver. If at all possible, I do not want to take a $250.00 gamble. Any advice would be appreciated. And just to double check, is it the "Dispenser" control board that controls the Internal LED lights???

Read More
john -
November 01, 2015
A:

We purchased a complete set of Kenmore appliances for our new home (including this refrigerator) last year end of August. The appliances were not delivered or installed until the end of November. About 6 months into use, the washing machine developed to small leak around the door gasket (while in warranty), but unfortunately did not call the problem in until two weeks out of warranty. Since that time, the low speed blower setting on the microwave vent has malfunctioned (blower stays on high for both high and low settings), and last week, our refrigerator began the "dsco" light strobing in both freezer and refrigerator . Like others, for the LED light issue, I attempted the 5 minute reset without the problem being resolved. Now the question is do we spend the money to replace a board, that like Mike's experience, may not resolve the issue. It seems to me that there can only be three potential issues: 1. the LEDs themselves (unlikely I believe), the switch, or a control board / driver. If at all possible, I do not want to take a $250.00 gamble. Any advice would be appreciated. And just to double check, is it the "Dispenser" control board that controls the Internal LED lights???

Read More
john -
November 01, 2015
A:

I bought subject refrigerator 2 yrs 3 mos ago. All 3 interior LED ights started blinking last week. I can turn on/off light switches and lights will sometimes stop blinking but will restart blinking after closing/opening door. Saw on parts list a light board, $90, but I do not know if this has anything to do with the LED lights. Above reply by "expert" mentions dispenser control board but that doesn't make sense to me. Anybody figure this problem out?

Read More
JOE -
November 22, 2015
A:

Same problem - strobe light effect drives me crazy! Seems this is a model defect as mine is barely 2 years old, and the "dispenser control board" answer has nothing to do with the lights....Unplugging the machine was also a stupid answer - Sears only "right" answer is to call their tech to come out and pay them a ridiculous service fee. If this is happening on all these same models it should still be warranted even after warranty is past. Sears used to have the best service in the industry - no more.....................

Read More
Phil -
December 24, 2015
See more answers
Q:

cutting deck spring locations 247.25000 (13A226JD099) - Craftsman Lawn Tractor (2012) (Sears)

A:

do you have a top view photograph of the mower deck which shows the springs for model 247.25000 craftsman riding mower

Read More
stan -
October 19, 2015