Model #2480 JENN-AIR Ranges, Electric

  • Elements & Grills
    3 Results
  • Controls
    3 Results
  • Top
    3 Results
  • Burner Box
    3 Results
  • Blower & Air System Parts
    3 Results
  • Counter Top Grill Range
    3 Results
Find part by diagram >

Question and Answers

Q:

Water just wont stop running but but not over flow WSM2480D3WW Ge Home laundry combo

A:

Thank You for contacting SearsPartsDirect.com. I do apologize for the delay in answering your question.

I know that it can be very difficult to have issues with your washer. This problem is called a siphon and it happens when the drain hose is shoved to far down into the standpipe. If the drain hose is stuck down the standpipe lower than the tub the water will fill and start to drain at the same time. If the hose and standpipe have a tight fight with no air gap the siphon may occur. Pulling the drain hose up should correct this problem. I hope this helps. If you need further assistance, please reply to this thread. Thanks for visiting SearsPartsDirect.com

Read More
Desirea -
Sears Technician
March 29, 2014
Q:

I need a manual for my Kenmore dishwasher model66513032k114. I didn't get a copy when the machine was purchased. I don't want to down 80 pages of paper.

A:

Thank you for submitting your question. I know having a manual is important and I will be happy to assist you. To receive a paper copy of your manual, I recommend contacting our warranty repair team to receive one. Manage My Life is a do-it-yourself troubleshooting repair site for Sears. We are unable to place orders or handle any warrantyr item issues. I hope this helps. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
August 17, 2013
Q:

Why is ice maker overflowing?

A:

I understand how it can be frustrating with the refrigerator ice maker overflowing with water. I have done some research on the Manage My Life website and have located a link similar to your issue. While you are waiting for a detailed reply from an expert I have provided the link below. Hope this helps!

Read More
Priscilla V -
July 02, 2012
A:

Thank you for submitting your question. I believe your issue is going to be with the water valve or fill switch. To verify, you can test the water valve with an ohms/volt meter. Here's a video on how to check the water valve. The water valve is part number 241803701 priced at $30.35 and the fill switch is part number 3206324 priced at $24.80. If you'd still like to clean the ice maker you can. You'll need to remove the ice maker from the refrigerator for proper cleaning. The image below will instruct you on how. Pleaser reply back to this thread if you require further assistance. Thank you for choosing Manage My Life.

Read More
Tykara -
Sears Technician
July 05, 2012
A:

Hi Tykara, While waiting for your response about a day ago, I had run my fingers to check for buildup at the bottom of the ice tray and was surprised to feel the unit very hot. It nearly burned my index finger. This was at the bottom of the unit along the inside edge. It surprised me and thought that it would be odd that this would be really hot in the freezer. I've run my fingers since then and it appears to be fine. Do you have any ideas as to what may be happening and with this additional information maybe you can pin down the problem more specifically.

Read More
Philip Fatato -
July 05, 2012
A:

The part you were feeling was probably the heater for the ice maker. The heater isn't the issue here. Please test the water valve as instructed and get back with me with your results.

Read More
Tykara -
Sears Technician
July 06, 2012
A:

Hi Tykara, I've tested the water inlet valve. It registered 375. I guess that it means it is failing. Can you confirm? If so, the part # you have listed is #241803701. My manuel shows 218959401. Please confirm. Also, do I have to order a fill switch as well? Thanks, Phil

Read More
Philip Fatato -
July 06, 2012
A:

Due to the age of your unit many of your parts have been substituted. So, the part numbers I provide for you may be different because of that. The water valve has tested good. Remove the cover to the ice maker (key #36) and try adjusting the timing stop screw (key #28) one turn clockwise to see if the fill adjusts itself. If the fill does not then the issue is with the holding cam (key #8) for your ice maker. What's happening is the holding cam is not allowing the motor to turn properly causing a delay and causing the ice maker to over fill. The holding cam will need to be replaced. You'll need to remove the mounting plate (key #5) to access the holding cam for replacement. The holding cam is part number 5304456661 priced at $5.92.

Read More
Tykara -
Sears Technician
July 07, 2012
A:

I'm not seeing the timing scew #28 on my model, however I do have a water fill adjustment screw, I think #30, in which I have already adjusted from an earlier suggestion with no change, other than smaller cubes. Please advise.

Read More
Philip Fatato -
July 07, 2012
A:

See how key #27 goes through keys 15 and 8? The adjustment for key #28 should be on the right side of the mounting plate. This is the diagram for your specific model. However, if you've already adjusted the fill with no change, this may be the same screw. I recommend replacing key #8 from here.

Read More
Tykara -
Sears Technician
July 07, 2012
A:

How do I order the holding cam #5304456661 from you.

Read More
Philip Fatato -
July 07, 2012
A:

You can order parts from the link provided below.

Read More
Tykara -
Sears Technician
July 09, 2012
See more answers

Top Parts