Model #2350 BISSELL Carpet/Floor Sweepers

  • Replacement Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Oil drain plug location 919762350 Craftsman Pressure washer

A:

Dear Frustrated, 

Thank you for choosing Sears and for contacting us with your question about the location of oil drain plug on your Craftsman pressure washer model 919762350. I am so sorry you are having trouble locating it.  I will be happy to help you with this. I have included the link below for you to view the owner’s manual online because it sounds like you may have the wrong manual. 

Under the engine maintenance instructions on page 12, the manufacturer states that the preferred method of draining the oil is from the top of the engine. There is an illustration showing which way the engine should be tipped. However, since you prefer to drain the oil from the bottom of the engine, that information is also provided. There is a drawing of the drain plug on that page. To locate the oil drain plug you will need to look at the bottom of the engine sump. Please view page 20 of the manual. The sump is reference 4 in the diagram. If you look inside of the box in the lower right corner the drain plug is reference key 15. I have included the link below for you to view a picture of the drain plug so you will know what to look for on the sump.

SAFETY WARNING: Make sure to follow the safety precautions in your owner’s manual when completing this maintenance. If you would prefer to have a technician complete the maintenance for you, you can set up service at www.SearsHomeServices.com or by calling 1-800-469-4663. 

I hope this answers your question. Thank you for choosing Sears, we appreciate your business. 
 

Read More
Rachel Morgan -
Sears Technician
July 11, 2015
Q:

My dishwasher keeps washing and washing and washing. It never stops washing, it never moves to rinse etc. What is wrong?

A:

The problem with the dishwasher can be very frustrating. I did some research on your model number but was not able to find a solution. Your expert will be able to help answer your question. It may take two business days. If you would like to look into Sears doing the repair here is a link for Sears Home Services. I do hope that everything works out on the dishwasher.

Read More
Marc -
April 02, 2013
A:

Thank you for your question and I understand your concern.

 It would be very odd for it to display "CL" while it's running. The "CL" indicates the door is open because the control does not detect the door switch(s) not closed. If you open the door while it's running, it will display "CL".

The rinse and hold cycle should run approximately 18 minutes which consists of 2 rinses. A normal wash cycle will run approximately 105 minutes or 1hr and 45 minutes under heavy soil conditions. 

 I added a link to the Use and Care Guide to reference the cycle times.

The heating element must heat water to certain degree (145) before the turbidity/thermistor will allow the wash cycle to proceed to the rinse cycles. The cycle times are approximate and will vary with options selected. The sensor will check the water temperature and if it's not hot enough, the time will delay while it heats the water. This will happen in the main wash in all cycles. This also happens even if HIGH TEMP wash has not been selected.

Check the incoming water temperature and it should be a minimum of 120 degrees entering the dishwasher. Also, check and confirm the heating element is working. I added an image below that may be helpful. 

The images below will also have water/service test cycle which I recommend running to confirm if the heater is working.

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.

Read More
Joey S -
Sears Technician
April 17, 2013
A:

Glo: I added the two images of the technical data sheet below.

Read More
Joey S -
Sears Technician
April 04, 2013
A:

We replaced the heating element in the bottom of the dishwasher. The new heating element is not getting hot at all.

Read More
Glo -
April 17, 2013
A:

It is also flashing back and forth from CL to 84 all the time sometimes the number counts down. The link to the care and use guide gives me cannot find page message.

Read More
Glo -
April 17, 2013
A:

Glo: I assume the heating element was replaced because it was not working. If the new heating element is not heating, it could have an open high limit thermostat, faulty control board or just a loose or burnt wire connection in the heater circuit. I recommend disconnecting the high limit thermostat and testing it with an Ohm meter for continuity. If the high limit measure continuity and there are no loose or burnt wire connections in the heater circuit, I suspect it has a faulty electronic control board. I added images in the last post which has the wiring diagram.

Read More
Joey S -
Sears Technician
April 17, 2013
A:

Glo: Is the dishwasher running when it CL and 84 is displaying? If so, it likely has a faulty electronic control board. Here is URL to the Use and Care Manual. Copy and paste this url address in your browser and it should come up. http://www.managemylife.com/mmh/owner_manuals/3735/FRIGIDAIRE-Dishwasher-L0308106?brand_name_search=gld2350rcs1

Read More
Joey S -
Sears Technician
April 17, 2013
A:

Yes, the dishwasher is running when it is flashing 85 CL, 84 CL etc

Read More
Glo -
April 19, 2013
A:

Glo; Based on the symptom; I would have to suspect a faulty electronic control board.

Read More
Joey S -
Sears Technician
April 19, 2013
A:

I have sears elite dishwasher 665134k710 model and it keeps washing. I have replaced the hi-temp thermal sensor under the tub and the controller and it still never cycles to rinse. It will cycle to off if started at a rinse cycle. The water is very hot and the washer stops and starts I assume it trying to since water temperature or what? Are there other sensor, relays that need replacement? Thanks, John

Read More
john redden -
March 21, 2015
See more answers
Q:

Moldy door seal WM2350HWC Lg Washing machine

A:

Thank you for being Sears’ valued member and for contacting SearsPartsDirect.com with your question about your LG washing machine model WM2350HWC. I am so sorry you are having a mold and odor issue with it. I will be happy to help you with this.

Unlike top load washers, all front load washing machines have a door gasket that takes some extra care. I have included the link below for you to view the owner’s manual online in case you don’t have a copy.

Owner’s Manual for LG Washer WM2350HWC

Please review pages 27 and 28 of the manual for instructions on cleaning the washer. I will be happy to highlight the key points for you.

After using the washer, wipe around the washer door opening, door seal and door glass with a towel or soft cloth. Be sure to wipe under the inside rubber seal to remove any moisture or soil.  It is important to allow the gasket to dry completely before closing the door.

Remove items promptly. Leaving laundry in the washer can cause wrinkling, color transfer and odor.

Run the TUB CLEAN cycle on a monthly basis. Please follow the directions on removing stains on the door seal with chlorine bleach. This will help remove any mold on the gasket and help prevent more from growing. If the mold returns, start running the clean cycle more frequently. After cleaning the washer it is important to wipe down the gasket with a towel or soft cloth to remove any water gathered in the folds of the gasket. Leave the door open to allow the gasket to dry completely.

I have included the link below for washing machine cleaner. This cleaner will help remove any build up in the tub and can also help remove odor. If the odor is persistent, you may need to complete several cleaning cycles.

Washing Machine Cleaner

If the odor persists then you may need to replace that gasket. Once you have installed the new gasket, the above outlined steps should prevent any future problems. I have included the link below for our guide to replacing the door gasket in case you need to do that. Please keep in mind that the guide is not specific to your model so some parts may look different.

How to Replace the Door Boot on a Front-Load Washer

I hope this answers your question. Thank you for choosing Sears, we appreciate your business.

 

Read More
Rachel Morgan -
Sears Technician
November 08, 2014