Model #22401 JENN-AIR Counter Grill, Electric

  • Control Panel
    3 Results
  • Top Assembly
    3 Results
  • Body
    3 Results
  • Blower Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

Vintage Craftsman Dual-Motion Industrial sander maintenance 31522401 Craftsman Dual - motion sander

A:

Thanks for the inquiry and for using SearsPartsDirect.com.
The two big maintenance items would be the belt and the motor brushes. Both of which have since been discontinued, but should still be available through aftermarket sources online or locally. 
Motor brushes are offered online, usually based on thier size. The same would hold true for the belt, it would be based upon the belt width and length. You could always run internet searches for the part numbers to see if there are any still in circulation. The belt is part number 622393-001, and the motor brush is 730352-003. 
Outside of those commonly replaced parts, cleaning the unit periodically will go a long way. Make sure there isn't any saw dust accumulation and occasionally blow it off with compressed air or clean it the best you can. 
Outside of that, the unit will need very little service. Hope these suggestions help and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
August 05, 2014
A:

Thanks for the inquiry and for using SearsPartsDirect.com.
The two big maintenance items would be the belt and the motor brushes. Both of which have since been discontinued, but should still be available through aftermarket sources online or locally. 
Motor brushes are offered online, usually based on their size. The same would hold true for the belt, it would be based upon the belt width and length. You could always run internet searches for the part numbers to see if there are any still in circulation. The belt is part number 622393-001, and the motor brush is 730352-003. 
Outside of those commonly replaced parts, cleaning the unit periodically will go a long way. Make sure there isn't any saw dust accumulation and occasionally blow it off with compressed air or clean it the best you can. 
Outside of that, the unit will need very little service. Hope these suggestions help and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
August 05, 2014
See more answers
Q:

Washer won't stop draining

A:

With the washer not working properly in your home cam be quite disappointing.I have taken the time to research on the Manage My Life website and have located several links that you may find helpful towards your issue. While you are waiting for a detailed reply from an expert I have provided the link below. Hope this helps!

Read More
Priscilla V -
April 23, 2012
A:

I know that it can be very difficult to have issues with your washer, especially when you need to use it. It sounds like your fill and drain hose connector is not properly snapping into place on the coupler that is installed on your new faucet. You may need to use a different adapter to hook up the fill and drain hose connector on this new faucet. Most plumbing or hardware stores will have various adapters that can be used on your faucet.

You could also have a failed fill and drain hose connector that would prevent the washer from filling properly. You may need to replace this connector.

I recommend that you disconnect the fill hose from the back of the washer. Hook up the drain and fill hose connector. Place the end of the fill hose in the sink. Turn on the water supply to see if you get proper flow and pressure through the fill hose end that is in the sink.

If you are not getting water flow through the fill hose, then you have verified that you have a problem with the drain and fill hose connector. If you do have proper pressure and flow from the fill hose, then you could have a problem with the fill valve or the control for your washer. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
April 25, 2012
A:

Anne, I think you're answering another question. My washer worked fine for a year. There is nothing wrong with the faucet. The pump continually runs so the tub cannot fill. I fixed a short in the wiring described above, though that may have caused some other problem. Thanks.

Read More
john -
April 25, 2012
See more answers
Q:

My Kenmore oven, model number 790-909-22401 coils do not heat up. What can it be?

A:

In reference to your Kenmore oven, model number 790.90922401;

The oven must be hooked up to 240 volts in order for it to work properly. The standard 120 volts will not allow for the unit to heat properly.

Usually, when an oven won't heat, it's because the element(s) is burned out. The bake element is the black, pencil- thick tube at the bottom of the oven. When the oven heats, the element glows red. This element has an expected life-span of several years. It may last for only one; it may last for many more. When the element burns out, you need to replace it.

The element is available for purchase at Sears Parts Direct .

Read More
Angela R. - Personal Solutions Manager -
Sears Technician
November 24, 2009

Top Parts