Model #2206 POWERWHEELS/PINES Toy riding

  • Replacement Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore Elite Calypso - Model 110.2206 etc. Panel shows "FL" and there is a hum - motor stuck. water in bottom will not drain. Will not reset. Model 110.2206

A:

 
Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when having trouble with the washer.
 
Glad to help out.   Im  looking at your Kenmore Washer model number 110.2206 etc.

The code "FL" (Over Fill) flashes---
The washer will beep every 10 seconds.  The pump will cycle 30 seconds on/30 seconds off until the over fill switch is reset or power is discontinued to the unit.  Press STOP/CANCEL to clear the display.  Shut off the water faucets to the inlet hoses if the water continues to flow.

(FL) OVER FILL CONDITION:

"FL" flashes if an over fill  condtion occurs.  This condition occurs when excessive water in the tub causes the flood switch to trip.  The control must realize that the trip was due to an over fill instead of a suds lock condition in order for FL to be displayed.

With an over fill condition, the beeper repeats a warning beep every 10 seconds with no time out.  The pump is cycled in drain mode for a half minute on, half minute off until the flood switch resets or power is discontinued to the unit.

on OVER FILL CHECKS:
1.  Verify the Pressure Switch is good with ohm meter.
2.  Check the Flood Pressure Switch.
3.  Check pressure hose.
4.  Check drain pump system.  Over fills could also indicate a failure to drain so check your drain hose and see if there is any blockage to the pump of foreign objects.


I hope this answers your questions but if you need further assistance please resubit another question with additional details.
 

Read More
Larry L -
Sears Technician
March 05, 2014
Q:

Why did my Kenmore Elite washer stop working?

A:

The full model number of your washer is on the model number plate of your unit. It would be in the format like the one in your detail (110.22062102). The owner's manual covers several different models. The last 4 digits of the model number pertain to colors and other details of the model. The "*" indicates that the owner's manual applies to all model numbers that begin with 110.2206 and 110.2408.

I included technical information below pertaining to your problem of no display lights even though the washer has power. Make sure that you have at least 110 volts of 60 Hz AC power supplied to the washer. Low voltage can cause problems with the control boards in the washer. The technical information supplied below should help a technician diagnose the current problem that you are having with the washer. This information is intended for technicians. I recommend having a technician use the information to diagnose your failure. Live voltage checks recommended in this technical information should only be conducted by a technician with the proper equipment and expertise to safely make the check.

You can order a hard copy of the tech sheet for this washer from the Sears PartsDirect website www.searspartsdirect.com . The part number for the tech sheet is 8530142. There is not a repair manual available for this washer. The tech sheet provides most of the information needed for a technician to diagnose and repair the washer.

If you need more technical help with this repair, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
August 08, 2008
A:

I'm having the same problem. Is there any chance you could post a larger version of the wiring diagram?

Read More
Justyn -
June 25, 2013
See more answers
Q:

Kenmore Elite Calypso model#110.2206 out of balance error at 5/6 minutes remaining. also stayed at 26/27 for quite a while.

A:

Washers are appliance that we turn to, to keep our clothes nice and clean. While you are waiting on an expert to answer your question, I was searching your model number and it seems to be in complete. A suggestion I have is to add complete model number to this thread for a better answer from the experts! Hope this helps!

Read More
Dezeray S -
July 11, 2011
A:

complete model # is 110.22064102 thank you for alerting me.

Read More
Frankie Beckwith -
July 11, 2011
A:

A number of problems could be causing that ob (out of balance) error code. You will need to open the lid before you can restart the cycle after that ob code appears. See if that code appears when the washer is run without any clothes loaded in it. If it does, I recommend that you run the diagnostic test mode shown in the first image below to see if it will drain and spin properly. If the washer is not draining properly, you can check the drain pump using the information in the third image. The second image shows how to access other components in side the washer. You can check the suspension components and you can remove the wash plate to check for problems. Be sure that you unplug the washer to disconnect electrical power before accessing internal components. This information may help you determine the cause of you ob and SL codes. If you need parts, you can order them from the Sears PartsDirect .

If you need more help, reply with additional details and we will assist you further.

This washer can sometimes be difficult to diagnose and repair on your own. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
July 12, 2011
A:

Hi Lyle and thank you for the diagnostic information. I've run thru it twice and it appears, both time, to complete the test. the end (at one second) the machine makes a rather abrupt noise when the basket stops; I assume this is all well and good. But I cannot tell if this is a normal 'at the end' noise. I am going to try a rinse only cycle to see if the problem is cleared. and in the meantime, I have called a service provider, but not Sears. thank you.

Read More
Frankie Beckwith -
July 12, 2011
A:

I'm running the empty machine thru a rinse and spin cycle only, without clothes, & it makes a real bad noise every time the basket stops moving. like a short, deep grind, noise. Sounds bad to me, and it is nothing I've heard before (but then, before the washer was located elsewhere and I never heard it running). BTW, the ob always occurs during the AUTO FLUFF mode at the end of the cycle and right now it is stuck on 7 minutes remaining...meaning it thinks there are too many suds, correct?

Read More
Frankie Beckwith -
July 12, 2011
A:

Usually if that timer stalls, it does indicate that the control is going into a suds kill routine or it is trying to balance the load. The noise that you are hearing at the end of the cycle could be caused by a bad bearing or a number of other failures. The component failure could be causing the motor control board to detect an unbalanced load or suds lock. The technician should be able to diagnose the cause of the noise. Once you have that problem fixed, there is a chance that the other codes will not continue to appear. If you need more help, reply with additional details. NOTE: This washer repair may become expensive. You may consider replacing the washer instead of repairing it.

Read More
Lyle W -
Sears Technician
July 12, 2011
A:

thank you Lyle. Cost of a new vs cost of the repair: I am taking into consideration. What do you think is too much to spend on the repair of an 8 yr old Kenmore Elite Calypso?

Read More
Frankie Beckwith -
July 12, 2011
A:

Frankly, I do not recommend that you spend any money fixing that washer. A rule of thumb for most appliances is not to spend more than 1/2 of the replacement cost when the washer is more than 1/2 way through its normal average useful life. A washer will normally last about 12 to 15 years on average. I would estimate that the Calypso model only lasts an average of 10 years. The universal joint and other components in that nutation type of agitation system tend to fail sooner than most other washers. It will probably be more economical to buy a new washer than to spend any money fixing that one. I hate to be so direct about that issue but that is my honest opinion. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
July 12, 2011
A:

I appreciate your directness and honesty. Please, if I may impose with one more question: do you think it a coincidence that I would find an enormous amount of sand in my washer and it NOT be a direct result of problems I am now having? I The city water supplier (small town) is blaming the builders and the plumbers. According to an independent plumber friend, he states he would be hard pressed to think this the fault of the builder or the plumber and that the sand can only get in one of two way: either from the water source (this is a new construction) or by someone putting sand in (which of course I did not) thank you for your time Frankie

Read More
Frankie Beckwith -
July 12, 2011
A:

Based on the limited information that I have from your description, I agree with your friend that is the independent plumber. If you have been using the water source and the plumbing in the house prior to this problem and did not see evidence of sand, then the likely source is from the water supply. You may be able to check with your neighbors to see if they have encountered sand in their water supply. Once the sand is flushed out of your lines, I recommend that you monitor your dishwasher and washer (unless you replace that washer). The sand could cause the solenoid water inlet valves to stick open. This would result in a flood of your laundry room and/or kitchen. You may need to check the inlet water screens on those appliances. You may also need to flush out the water heater. I hope that this information helps. If you need more assistance, don't hesitate to ask. We are here to help you with whatever you need.

Read More
Lyle W -
Sears Technician
July 12, 2011
See more answers