Model #215921 KOBALT (COLEMAN) Air compressor

  • Compressor Assy
    3 Results
  • Manifold
    3 Results
  • Motor Assy
    3 Results
  • Motor/tank/pump/wheels
    3 Results
  • Pump Assembly
    3 Results
  • Pressure Switch/gauge/valve
    3 Results
Find part by diagram >

Question and Answers

Q:

My Kenmore washing machine doesn't spin/drain on all cycles

A:

I know if I was in your situation I would be so frustrated and would not know what to do. So, I did some research and I found a link that might answer your question in the Manage My Life website. I'm attaching the link below, I hope this helps!!!!!!! http://www.managemylife.com/mmh/questions/215921-washing-machine-drain-spin-2

Read More
Raquel F -
November 01, 2010
A:

Thank You so much for the link, I will check it out.

Read More
Anonymous -
November 01, 2010
A:

Thank you for your question.

I am sorry to hear you are having a problem with your washer. The most common cause would be a defective lid switch but you are correct it could be a timer problem. If the motor does not make any sounds in the spin cycle, I suspect the lid switch is the problem. If the lid switch is broken, the washer will still fill and agitate but when it gets to the drain and spin the washer will stall. The timer would not advance to off either. A quick check you can do is to run a cycle with the lid switch jumped. If the washer operates, the lid switch needs to be replaced.

To jump the lid switch you need to unplug the washer and open the console. I have provided you with the instructions for opening the console below. Once you have the console open, locate the connector for the lid switch. Place an insulated jumper between the gray and tan wires. Not the green it is a ground and will cause a short. After inserting the jumper make sure it will not touch anything metal, plug the washer in. start the washer in a cycle, and let it go. If the washer completes the cycle, you need to replace the lid switch. Do not leave the jumper in while you are waiting for the part. The jumper is only of the test.

To you replace the lid switch you have to remove the cabinet of the washer. The instructions for that are also in the image below. Once the cabinet is removed you can take the screws out securing the lid switch and remove the harness from the clips along the underside of the cabinet. Then reinstall the lid switch in the reverse order. Before you reassemble the cabinet, please read the instructions for installing the cabinet provided in the image.

I hope this is helpful. Please reply below if you need further assistance. Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
November 01, 2010
A:

Mark, Thank You so much. You were 100% correct, The Lid Switch was bad. I'm going to order the switch from the link you provided.

Read More
Anonymous -
November 01, 2010
A:

I am glad you have found the problem. Please let me know if you need anything else. Mark T.

Read More
Mark T -
Sears Technician
November 01, 2010
See more answers
Q:

My Kenmore washing machine doesn't spin/drain on all cycles

A:

I know if I was in your situation I would be so frustrated and would not know what to do. So, I did some research and I found a link that might answer your question in the Manage My Life website. I'm attaching the link below, I hope this helps!!!!!!! http://www.managemylife.com/mmh/questions/215921-washing-machine-drain-spin-2

Read More
Raquel F -
November 01, 2010
A:

Thank you for your question.

I am sorry to hear you are having a problem with your washer. The most common cause would be a defective lid switch but you are correct it could be a timer problem. If the motor does not make any sounds in the spin cycle, I suspect the lid switch is the problem. If the lid switch is broken, the washer will still fill and agitate but when it gets to the drain and spin the washer will stall. The timer would not advance to off either. A quick check you can do is to run a cycle with the lid switch jumped. If the washer operates, the lid switch needs to be replaced.

To jump the lid switch you need to unplug the washer and open the console. I have provided you with the instructions for opening the console below. Once you have the console open, locate the connector for the lid switch. Place an insulated jumper between the gray and tan wires. Not the green it is a ground and will cause a short. After inserting the jumper make sure it will not touch anything metal, plug the washer in. start the washer in a cycle, and let it go. If the washer completes the cycle, you need to replace the lid switch. Do not leave the jumper in while you are waiting for the part. The jumper is only of the test.

To you replace the lid switch you have to remove the cabinet of the washer. The instructions for that are also in the image below. Once the cabinet is removed you can take the screws out securing the lid switch and remove the harness from the clips along the underside of the cabinet. Then reinstall the lid switch in the reverse order. Before you reassemble the cabinet, please read the instructions for installing the cabinet provided in the image.

I hope this is helpful. Please reply below if you need further assistance. Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
November 01, 2010
See more answers

Top Parts

Top Accessories