Model #2042 GENIE Garage Door Opener

  • Powerhead
    3 Results
  • Rail/chain/belt
    3 Results
  • Service Parts
    3 Results
  • Service Parts
    3 Results
  • Service Parts
    3 Results
  • Service Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

What is the correct 2 bin bagger for Husqvarna tractor model number 917.279240?

A:

According to our cross reference material, you need bagger number 24897.

Read More
Landell -
Sears Technician
November 30, 2009
A:

That is not the correct bagger for the YTH20F42T. Any bagging system with support post part number 180923 or replacement 180923x479 is not going to work. Sears is unable to come up with a bagger that will fit the YTH20F42T.

Read More
Morningwood -
November 05, 2011
A:

I have cross referenced our 2011 tractor fit up chart and according to it you need; part number 24891 (bag) 2 bin soft bag; Optional 3 bin soft bag (part number 24892); optional 2 bin hard buckets (part number 24897).

Read More
Landell -
Sears Technician
November 07, 2011
A:

I don't doubt that is what the cross reference says and if my tractor was model # YTH2042 it would be correct. Unfortunately, the "F" in YTH20F42T indicates that it has a fabricated (not stamped like the non-F model) deck and none of the part numbers you mention will work. The problem isn't even the chute... my tractor has and angled back plate, all the bag support posts that Sears carries are for a straight vertical back plates.

Read More
Morningwood -
November 07, 2011
A:

FYI...for the YTH20F42T (F model) the Grass Catcher Model Number is GTT342 or Product No. 960 72 00-11 or Mfg. ID No. 96072001100.

Read More
KEN -
July 26, 2014
See more answers
Q:

Pressure Switch Replacement 106153780 Craftsman Sears twin cylinder tank type paint sprayer

A:

Thanks for the inquiry and for using SearsPartsDirect.com.
Sorry to hear of the defective pressure switch, I know how frustrating that is to have occur.
Based upon our internal system for pressure switch CW-2042, I see that there is a substitution offered of 158J5. The system states that you may need to purchase longer 1/4" tubing to make it work properly, but doesn't identify the part number for the tubing. 
For convenience, I have provided a blue link below that you may click on to be directed to the SearsParts site to view and purchase the pressure switch being recommended for the unit.

Pressure Switch 158J5

Hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
June 02, 2014
Q:

don't started, i don't have electricity to crank PB2042YT Poulan Tractor

A:

Thank you for your question.

 

 

I am sorry you are having this problem with the tractor. I recommend determining what is causing the engine not to turn over. First, make sure the engagement lever is down or the PTO button is pushed in and the brake pedal is fully depressed or the tractor will not attempt to turn over. If you have already done this, I recommend checking the fuse. The fuse is located behind the dash. If the fuse is good, you have a wiring or switch problem. The easiest way to pin point the problem is with a volt meter. If you do not have a meter, you can purchase one relatively cheap.

 

Turn the meter to check dc volts, and then hold the black lead to the black negative battery terminal for all of the voltage checks. Place the red lead on the positive terminal of the battery. The reading should be 12 volts. If you have a 12 volt reading, move the red lead to the first blue dot in the image. Your reading should be 12 volts. If you have 12 volts, have someone sit on the tractor and hold the brake pedal while turning the key for the rest of the checks. While they have the key turned to the start position, move the red lead to the next blue dot. The reading should always be 12 volts. Then move to the next blue dot. If you lose the 12 volts, the problem is between the last blue dot you had the voltage and where you lost the voltage. If you have 12 volts all the way to the white wire on the solenoid, the solenoid or the starter is defective.

 

To determine starter or solenoid short the two large posts on the solenoid together with a screwdriver. There should be a spark it is normal. Once shorted the starter should run. 

 

If the tractor still will not run once you get the starting issue fixed, please let me know. I will be happy to assist you with diagnosing that.

 

 

 

If you need to order parts for the tractor, you can do so from the following link. Replacement parts for a Poulan tractor model PB2042YT.

 

I hope this is helpful.  Please let me know if you need further assistance.

 

 

 

Thank you for using Manage my life.

 

Mark T.

Read More
Mark T -
Sears Technician
October 08, 2013

Top Accessories