Model #18391579 KENMORE Under Counter Refrigerator

  • Cabinet Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

How many watts is the 18391579 beer dispenser? 18391579 Kenmore Refrigerator

A:

Also, will I need to worry about the frequency change (60Hz to 50Hz)? Is the motor tolerant of running in a 50Hz environment without too much degradation, or more importantly, catching on fire?

Read More
Clinton -
May 20, 2014
A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help you. Upon researching model 18391579 the voltage and wattage should be listed on the model tag or by the compressor label.

If you have any further questions please re-post. Thank you for choosing Sears. Have a great day.

Read More
Samantha A -
Sears Technician
May 22, 2014
A:

The voltage says 60hz, but sometimes the motors are wound to take either 60 or 50hz even though they are not labeled as such. Can you find out if this motor is wound to take 50hz as well? If not, then I cannot use the appliance. Thanks!

Read More
Clinton -
May 23, 2014
See more answers
Q:

kenmore refrigerator

A:

No worries! Manage My Life is here to help! An expert will be able to provide you with a detailed answer to your question. It usually takes 24-48 hours to receive a response. Have a great day!

Read More
Jackie S -
September 01, 2011
A:

We don't have any installation instructions for the compressor. I am sending an image showing the refrigerant flow for the refrigerator.

If you are not comfortable replacing the compressor, you can go to Home Services and get a Sears technician to repair the refrigerator. You can find the nearest location of a Sears Repair Center.

Read More
Jimmy K -
Sears Technician
September 03, 2011
A:

the copper line coming from the condensor which port does it go to the highest port or the lowest port ?

Read More
Roger -
September 08, 2011
A:

Roger, connect 120 volts to the compressor, remove the plugs from the tubing and let the compressor run a short time. One of the ports will blow air, that is the port the line from the condenser connects to. The other tubes should suck and they are for the suction line and process tube.

Read More
Jimmy K -
Sears Technician
September 08, 2011
A:

whats the process tube used for ?

Read More
Roger -
September 08, 2011
A:

This is the line you can clamp a valve on to check pressures the crimp it and solder it after the job is complete.

Read More
Jimmy K -
Sears Technician
September 08, 2011
See more answers
Q:

Ask your own question or join this conversation

A:

I know how important it is to have your appliances working properly so that you can use them any time you want. While you are waiting for an expert answer, I suggest you look in your owners manual in the troubleshooting pages. Below is a link in where you can enter your model number and your owners manual will pop up. I hope my link is useful.

Read More
Joseph P. -
January 10, 2011
A:

Thank you for your question.

Not getting the tap to work can be a puzzle sometimes.

  • the first thing I would check seeing as you have some beer when you open the CO2 line is to remove the regulator hose and look at the screen inside to make sure it is not waxed over and even though the gauge shows 12 pounds you may not be getting much volume out of the regulator.

How long has it been since you cleaned and sanitized the sankey and head valve assembly cleaned. It should be done ever week or if the Kegerator has not been used for awhile.

I will give you a link to a website about the use and cleaning of keg tap systems.

KegMan .

I hope this will help.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
January 12, 2011
A:

The kegerator has actually never been used. The guy I bought it from had never even assembled it. I checked all the lines and they are all clear of obstructions.

Read More
Ian -
January 12, 2011
A:

Thank you for the update. You should have two gauges on the manifold, tank pressure and CO2 pressure to the keg. It really sounds like you do not have any CO2 pressure to the keg. All the lines fit up the way they are suppose too. And the sankey is locking in place. Make sure the air vents are clear. I am hoping that the keg is a store bought beer keg and not a home brew keg retrofit. If that is the case you will never get the check ball to push down. You are sure that you have all the parts. If the box was never opened I would think it would be ok. I am sorry but I am running out of ideas. You may have to have a technician check out the unit. But if and when you find the problem please let me know if you will. Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
January 12, 2011
A:

I appreciate the all the help. I'm only seeing one gauge on the CO2 manifold, so it very well may be the pressure output that's holding me up. I'll probably have a technician come out and take a look at it. Thanks again!

Read More
Ian -
January 12, 2011
A:

Thank you for the update. So you cannot tell how much pressure is in your CO 2 tank? You can take the connector off and open the valve and you should have a LOT of pressure. If you do not you are out of CO2 and you may have only had 12 psi in the tank. If this is not the problem, as you said you will need a technician to see what the problem is. Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
January 12, 2011
See more answers