Model #18310679 KENMORE Under Counter Refrigerator

  • Cabinet Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

What is the part number for the power board in my wine cooler model 183.10679?

A:

I have checked on the PCB board for this wine cooler. The parts list diagram on our system shows that it needs control board part number RF-0668-34. I also see research that shows that the control board RF-5210-11 should also work in this wine cooler. We checked directly with the manufacturer (Haier) and found out that an exact replacement for the original control board is not available for this wine cooler. It is my understanding that the correct replacement board for this wine cooler is the one that is listed in the Sears parts system (RF-0668-34). If you were to attempt to replace the control board in this wine cooler, the new wiring connections would have to be soldered directly onto the new board since the wiring connections are not the same as the old control board. This is not a practical and cost-effective solution for the problem in this situation. I recommend that you replace the wine cooler instead of attempting to repair it since a practical replacement for the control board is not available.

Read More
Lyle W -
Sears Technician
December 18, 2009
A:

I don't know if you still need it but I think I have the board that you need and you have the one that I need. post back if you still need it.

Read More
Terry -
August 14, 2010
A:

RF-5210-11 Will work the number on the board by the input connector should be a CD-110-C it's the one in the picture on the sears parts direct web site!!! THE ONES They sent me have that number crossed off with a black marker the number on these boards are CD-220-C they sent me two of them like that They are 220 Volt boards. I Changed the board over to 110 volt by putting jumper J110 in its between the larger capacitor and the diode right above the power input connector! The Part number for the board well the manufacture of this particular board is HYS60-12-KD it is a 220-240 Volt AC input 12 volt 5 amp DC output. I put that jumper in and it works just fine on 110 volts now before i did that the fans would spin intermittently the light would blink and it would buzz or hum. From what i can tell they ordered the wrong boards or got the wrong boards. The only other thing i can think of is the fuse might need to be changed to a higher amp rating drop the voltage of the supply and it will draw more amps.

Read More
Dennis -
May 14, 2013
See more answers
Q:

Replacing power PCB

A:

Managemylife.com is always a great resource to find the answers to just about anything. I was unable to locate any useful information for you at this time. An expert will research your question and respond within two business days but usually sooner. Have a great day!

Read More
Alina F. -
June 26, 2012
A:

Thank you for your question. I can understand your concern about the board. Sometimes a replacement part will be a little different then the original. When this occurs, if there is anything important that needs to be done, it will have instructions included. In this case, it would seem the wire you are referring to will not be needed with this new board. With some of these controls, there may be an extra wire that is intended for factory use only, to make some internal checks. This will not cause a fire. I hope this will help you.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Scott D -
Sears Technician
June 28, 2012
A:

Thank you for the information!

Read More
Anna -
June 28, 2012
A:

Anna, thank you for using Manage My Life.

Read More
Scott D -
Sears Technician
June 29, 2012
A:

I just started using the wine cabinet again, and while it turns on and I can set the temperature, the temperature is staying constant and is not dropping to the temperature that I set. Could this be linked to the replacement of the power PCB? Also, should I get a wire nut or something like that to cover the naked wire? Thank you!

Read More
Anna -
September 05, 2012
See more answers
Q:

What's wrong with my wine cellar?

A:

Thanks for the model number. This is a thermal electric unit which has no compressor. I'm sending you some information from the owner's manual that is very important for this type of wine cellar. There must be sufficient air circulation and the ambient temperature must be no higher than 77 degrees just to maintain 50 degrees. If there is sufficient air clearance and the temperature is below 77 degrees, the most common problem is the PCB board # RF-0668-35. It's possible the fan may failed but it's rare. The board usually needs to be replaced. This board is available at SearsPartsDirect . If you need more assistance, please resubmit your question, with additional details.

HA_DH_Beverage

Read More
Erin S. - Editor -
Sears Technician
June 29, 2010
A:

Hector, did you order this part and if so did it fix the problem?

Read More
Joe -
July 22, 2012
See more answers