Model #17 SEARS Swimming Pool Accessories

  • Replacement Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Ice maker will not freeze water OR dump the tray 79572032110 Kenmore Refrigerator

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your ice maker is not working properly in your refrigerator. 

I have found information that will assist you. I recommend testing the ice maker to see what is wrong.

 1. Check the temperature of the freezer becasue if it is fewer than 17 degrees F it wont make ice.

 

2.Check if your water fill spout is plugged with ice, if it is then it wont make ice.

3. Check to see if water is getting to the water inlet valve.

4.Use an OHM meter to check the continuity of the water inlet valve. If it does not have any continuity then you need to replace your water valve. If it does then the icemaker itself is the problem and may need to be replaced.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
May 22, 2015
A:

my display shows ER 1F I changed filter but cannot get the display to reset what do I need to do?

Read More
Ken miller -
January 29, 2016
See more answers
Q:

Anode rod for model 153.331472

A:

Thank you for your question. I'm sorry you are having this odor in the water and I can understand your concern. The anode rods currently in the water heater are made with magnesium. The less active anode rod to correct this problem, which is made with aluminum, is # 9001453. It's not essential but I would recommend replacing both anode rods (same rod). I also recommend chlorinating the tank. Here is the procedure to chlorinate the tank: Be sure the water supply valve has been closed and set the thermostat to pilot only. After removing the existing anode rod (rods), household bleach must be added to the water heater tank at a ratio of one (1) cup for every (5) gallons of water heater capacity. Bleach may be poured directly into the anode opening or through any other water fitting on top of the tank. Install the new less active anode rod (rods) and refill the tank completely. Turn on each hot water tap slowly and allow the water to flow until the chlorine can be detected. Turn off the hot water taps and let the water stand in the hot water distribution piping for no less than 2 hours (Preferably 8-12 hours). Flush the complete hot water distribution system through each hot water tap after the chlorination treatment. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

 
Read More
Scott D -
Sears Technician
November 21, 2013
A:

Would this part and procedure also apply to model 153.331572 I just realized I have the 50 gallon model.

Read More
Anonymous -
November 21, 2013
A:

Yes, the anode rod part and the procedure will be the same. If you would like more assistance, I will be glad to assist you further.

Read More
Scott D -
Sears Technician
November 22, 2013
A:

Would part number 9001453 also apply to the second anode which is part number 9003934 only reason I ask is it looks like at the top there isnt a hex head which appears different.

Read More
Ryan -
March 10, 2014
A:

I purchased a new anode rod for my 5 year old water heater, when I removed the old one, it was twice as long as the new one. There was no wear on the old rod so I put it back in. The OEM rod is 33" and the new one I ordered from Sears is 17". I can email you photos.

Read More
bruce -
January 29, 2016
See more answers
Q:

I need a manual for a Kenmore 317B6034. My oven does not heat, I need to make sure I am turning on my oven correctly.

A:

Having the owners manual is always great to have. The problem with the oven not heating can be frustrating. I did some research on the 317B6034 but was not able to find the manual. Your expert will help answer your question. It may take two business days for your expert to reply. I do hope that everything works out.

Read More
Marc -
July 19, 2013
A:

I can most likely help you with this problem but I am having problesm bringing up the 317B6034 model number.  The number seems more like a serial number.  Please confirm the model number and reply below for further assistance. 

Read More
Fred M -
Sears Technician
July 21, 2013
A:

That model number is valid. I have the exact same model, there is no serial #, but I'm sure it's pretty old. It came with the house that I live in, and I've been here 17 years. The issue I have is my stove burners work, the broiler works, but the oven won't turn on. The light near the knob turns on, but the oven doesn't heat up, and there is no smell of gas at all. What could that be?

Read More
Tom -
December 05, 2014
A:

I have an old Kenmore gas stove/oven with electric ignighter to light the oven and 4 burners. for some reason the ignighter is not working now. how do I get it to start working again. I was trying to locate a manual but I cannot find the model number. all I found is a serial number in the oven. SN 317B6034. where can I find the model number? thanks

Read More
FRANK -
January 20, 2016
See more answers