Model #15-2000 DP Misc Exercise

  • Base Assembly
    3 Results
  • Carriage Assembly
    3 Results
  • Lower Pulley Bracket Assembly
    3 Results
  • Weight Support Assembly
    3 Results
  • Pulley Wheel Assembly
    3 Results
  • Wall Mounting Bracket
    3 Results
  • Wall Mount
    3 Results
  • Pulley Bracket Assembly
    3 Results
  • Replacement Parts
    3 Results
  • Handle Accessories
    3 Results
  • Weight Support Assembly
    3 Results
  • Pulley Assembly
    3 Results
  • Short Pulley Bar
    3 Results
Find part by diagram >

Question and Answers

Q:

Sears Kenmore Electric Range the bake element doesn't get hot

A:

I can understand the importance when it comes to your range. I have attached a link below to manage my life that has great information that can be helpful when it comes to replacing a baking element. Hope it helps! http://www.managemylife.com/mmh/questions/113331-replace-bake-element-range

Read More
Maira E -
November 10, 2010
A:

Thank you for your question.

I can understand not being able to be able to get the bake element to work.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

  • I would suggest since you have a meter and know how to use it safely with or with out the power on, please set the meter to the 240 volt scale.

  • Make sure that any wiring you have disconnected is all re-connected like the range would be ready to run.

  • With the back cover off the control panel and the range connected to the power source.

  • Set the oven to the bake setting.

  • Put one meter probe on the P2-3 L1 connection on the control board. Put the other meter probe on P2-4 red wire coming from the element on the control board. If you have 240 volts, the relay on the board is not closing and will need to be replaced.

  • To prove this, set the oven to broil and put your probes across P2-2 black L1 to P2-1 Blue from the broil element.

I hope this will help with your oven repair.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
November 11, 2010
A:

I also have this range, model # 66595775890. The number printed on my control board is: 60C06510106 My broiler has stopped working, bottom element works fine. I check the resistance on the broiler element and it appears to be in spec, it was last week so I've forgotten exactly where it registered? From the broiler connections on the back to ground I'm getting 120 volts. Following your instructions above, I did the following: I don't have a P2-3 L1 connection on my board, so I set the oven on Bake and measured voltage between P2-2 L1 black to P2-4 red, it roamed between 2 - 4 - 5 volts. The K-1 solenoid clicked closed and the K-2 solenoid (Broiler) would click on & off. Next I set the oven to Broil and measured between P2-2 L1 black and P2-1 blue, that measured at 240 volts. The K-2 solenoid clicked closed and stayed there. I could feel a tiny, tiny bit of heat in the element. It appears to me that the solenoids are working fine other than the Broil solenoid in Bake mode, not sure if it is normal for it to click in & out? Any thoughts? Suggestions? I appreciate your response in advance.

Read More
Barry -
May 08, 2013
See more answers
Q:

I have a Craftsman riding mower model number 917.270743. What is the approximate age of this mower?

A:

I know this type of information can be very helpful for you to have. While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question.

Read More
Yadira B -
April 03, 2013
A:

Serial number is 061500D 007002. So the manufactured date is 06-15-2000?

Read More
DougWR -
April 03, 2013
A:

Thank you for contacting ManageMyLife.com regarding the age of your Craftsman riding mower. I see Yadira provided you with some excellent information. This unit was manufactured on June 15, 2000.

I really hope this information helps you today. Thank you for using ManageMyLife.com.

Read More
Korinna S -
Sears Technician
April 03, 2013
See more answers
Q:

Check engine light/ car RPMS to high

A:

I know that keeping your car running is very important. While you are waiting for your expert answer, I did some research on the problem. This is not normal for this type of car, and it ususally means a problem with the transmission. The only way to know is to take it to a mechanic. I hope this helps.

Read More
aashe -
September 20, 2011
A:

Iv thought of taking it to a mechanic but will be pricy, thank you, i will wait for expert

Read More
Roman -
September 20, 2011
A:

sounds like it needs a tune up and air filter new plugs and wires or bad coil pack could be going bad at 70mph rpms will be at 3thousand or higher because of the horsepower of the engine if it was in the 5 or 6 thousand mark i would say you have a problem but if its at 3 that is normally where it would be at 70 at 55mph it would be at 15 to 2000 rpms and if its at 60 to 65 it would be around 2100 to 2500 rpms so it sounds like the rpms are fine but you have a miss in the engine which if you give it a tune up that cold cure the problem also it will make the engine light stay off unless its a faulty sensor good luck hope this helps you

Read More
john -
September 20, 2011
A:

Thank you john, great help

Read More
Roman -
September 27, 2011
A:

Yes the RPMs are correct and the check engine light is an indication that the computer is seeing something that it sees as a hazard to how the car is running. Such as running too lean or rich. There should be a code set in memory so that this issue can be further diagnosed.

Read More
MikeLangton -
Sears Technician
October 22, 2011
See more answers