Model #14300 BROWER Poultry Equipment

  • Reel Assembly
    3 Results
  • Valve Body
    3 Results
Find part by diagram >

Question and Answers

Q:

why is my freezer over freezing? It is 25 below zero.

A:

I'm sorry to hear that you are having some difficulties with your freezer, over freezing can ruin your food. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assistance for you.

Read More
Joseph P. -
December 29, 2011
A:

Thank you for your question. I understand your concern about the temperature. This model shows to have a control board, which means that either the board has failed or the sensor. The sensor can be checked by placing the board into a diagnostic check. Press the on/off pad and filter reset pad at the same time for 3 seconds. This will set the diagnostic check at step 1, which is the freezer thermistor check. I'm attaching the information for this check below. If it passes, the control board # 8201528 will need to be replaced. If it fails, replace the sensor # 2188819. To exit the diagnostic mode, disconnect the power for 30 seconds and then reconnect it. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Scott D -
Sears Technician
December 30, 2011
See more answers
Q:

Kenmore Elite Duel Fuel Range - 790.41103100 - Clicking clock when door opens

A:

When it comes to appliances making strange noise and not working properly can be really frustrating. While you are waiting on an expert to answer your question, a suggestion I have is to visit Sears Home Services website to set service with a Sears technician. I have attached the link below. Hope this helps!

Read More
Dezeray S -
June 01, 2011
A:

Thank you for your question and I understand your concern.

You�re describing a very unusual symptom. If everything else is working properly when the door is shut I would have to assume the electronic oven control is faulty providing this did not begin after any service was performed or parts replaced. If this symptom started after having your range service then it could be caused by a loose wire connection or a miss-wired component.

I recommend calling and setting up a service appointment to diagnose and verify my assumption. The electronic oven control board is part #31657703 at the approximate cost of $143.00.

If you do not feel confident repairing this problem yourself, then you can have it repaired by a Sears technician. Here is a link that will provide the nearest drop-off locations: Sears Home Services .

Read More
Joey S -
Sears Technician
June 02, 2011
See more answers
Q:

Sewing Machine Operating Manual

A:

Moving can cause problems with many of our products and I can understand how upsetting this can be when it happens. I was able to locate the manual for your model here at Manage My Life. I downloaded to the link below. If you have any problems accessing this, just reply here and the expert may be able to e-mail it to you. Hope this helps with the sewing machine and that you get settled in without too many further mishaps.

Read More
Barbara H. -
May 08, 2011
A:

I believe the owner's manual will help you with this problem.

You can view the manual at the following link: http://www.managemylife.com/mmh/owner_manuals/2247/KENMORE-Mechanical-Sewing-L0909123?brand_name_search=158.14300] .

I hope this helps but reply with any additional questions for further assistance.

Read More
Fred M -
Sears Technician
May 09, 2011
See more answers