Model #13953930DM CRAFTSMAN Garage Door Opener

  • Rail Assembly
    3 Results
  • Installation Parts
    3 Results
  • Motor Unit Assembly
    3 Results
  • Accessories
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

cannot get the 1395390DM to sync with my Audi MDX wireless control. 13953930DM Craftsman Garage door opener

A:

Cannot program older Sears remotes to new opener. I have two other openers and three other remotes and none of the remotes will program to the new opener. Any suggestions?

Read More
Wayne -
January 25, 2016
Q:

Why won't my remote open garage door?

A:

Garage door openers are a great convenience. They are also added security. It can be a hassle when the remotes stop working. I was able to find some information for you. I am adding the links below to help you with your question while you wait for your expert response. I hope this will help you out.

Read More
Marc H -
April 08, 2012
A:

First, check if both safety sensor LED lights are a steady green. If one is not, then align them to one another until the green light shows steady. If the sensors are fine then change the battery in the remotes and re-sync it to the opener. If the opener still does not work after that then, let's try this:

  • Hold down the "learn" or "SRT" button on the back panel of the main unit until the LED goes out (about 6 seconds). That will clear all the codes from the opener memory.

Now program in the remotes by doing this:

  • Press and release the "learn" or "SRT" button (the LED will blink) and within 30 seconds, press and hold the button on the remote until the lights on the opener blink.

Now the remote should be programmed in and you can try it. If it does not work, there is most likely a problem with the logic board of the motor unit and it will need to be replaced. I hope this helps. Thank you for using Manage My Life!

Read More
Tykara -
Sears Technician
April 11, 2012
A:

I am having a similar problem with a similar model (139.53930DM). I've tried to reprogram according to the manual by holding down the learn button. I saw this reply and noticed that one of the sensors is not green it's orange, but I can't move it to make it green. Any suggestions? Thank you.

Read More
Lara -
May 27, 2013
A:

Lara, some have both green and some have a green and a amber or orange colored led light but as long as you have a led lit on both the sensors are ok. the sensor circuit only works when closing the door not opening the door. so you have another issue. if the battery is ok in the remote have you changed any light bulbs in the opener, the newer style light bulbs will cause interference with the RF signal from the remote. also try the remote close to the opener unit to see if it is a signal range issue. you can look on the logic board that's the board on the back of the opener with the wire hanging down some models it is on the side of the opener but will have the small wire hanging down from it. that logic board has a small led light right above the learn button it is a diagnostic light and when you press the remote button to open or close the door it should flash quickly and will tell you if the remote is sending a signal out if there is no flashing the remote battery or the remote is bad and not sending any signal. check those couple of things and post back for further info depending what you find out. also you may want to erase all codes from the opener by holding the learn button in for about 10 seconds this will erase all codes from the opener and then reprogram the remote by waiting for the light above the learn button to shut off and just press and release the learn button quickly then press and hold the remote button until the main lights on the opener flashes then try the remote.

Read More
TC -
May 27, 2013
A:

Thanks for your reply TC. I've replaced the battery even though both remotes don't work. I've tried reprogramming by hitting the learn button, but no lights go on and no noises are heard. I've also tried as you suggested and hit the remote close to the motor unit, but nothing happens and there are no blinking lights indicating a signal. Of course the unit is just over a year old, so it is no longer under warrantee. It just stopped working. Please let me know if you have any other suggestions. Thank you!

Read More
Lara -
May 28, 2013
A:

My wall mount and the wireless key pad both work to open and close the door. neither of the remotes work. i changed the batteries and tried to reprogram both remotes and they still wont work. any suggestions?

Read More
kip -
November 29, 2015
A:

Regarding the 3 function remote. I can program the remote opener with the large push button but openers will not accept a sync to the two smaller buttons from other garage door bay units.

Read More
Robert -
December 29, 2015
See more answers
Q:

13953930DM light won't shut off 13953930DM Craftsman Garage door opener

A:

Same scenaio in my case per post on Oct 13, 2015 - light will not cycle off after 4.5 minutes, but rather stays on all the time. Sensors working fine. Caused motor unit to respond with error code once (light blinked 5 times in succession). Had to unplug unit for a few hours, then plug back in to reset.

Read More
Jeremy -
December 08, 2015

Top Parts

Top Accessories