Model #13953716 CRAFTSMAN Garage Door Opener

  • Unit Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Key pad no longer works 13953716 Craftsman Touch code lock

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your garage door opener. Upon researching model 13953716; the keypad for this model has been discontinued and is no longer available, we do not have a substitution.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
August 04, 2015
Q:

How do I reprogram my keyless entry for my garage door opener? I have no entry button on the pad.

A:

I am not sure exactly what type of keyless you are dealing with since that number did not run as a valid model or part number for me in our systems here.

The keyless that should be used with that model, a 139353876, does have an enter button. And, as you can see in the images below from your Owner's Manual it does use that button as part of the programming procedure.

And, unless the keyless you have plugs into the house power rather than using a battery as most do, a lightning strike should have had no effect on it. Any surge through the opener itself that erased the memory would have erased it for the remotes and the keyless at the same time, which is not what I understood to have happened based on your question.

Either way, if this keyless worked before and uses a battery and the remotes will program in then you should be able to program the keyless to work again.

Most keyless entries require some standard button be pressed to confirm the complete code was entered and to send the signal. So if there is no Enter button then there should still be another button you used to press to activate the door after you entered your code. And you should be able to use the programming procedures in your manual and just substitute that particular button for the Enter button in the procedures.

If not, then maybe the keyless battery was barely strong enough before to send a signal and is now just too weak to maintain the signal through the programming process. You might want to try a new battery to see if that helps. Or, you could try erasing the memory on the opener and reprogramming in all the remotes and the keyless as noted in the links below in case the memory is just full for some reason.

If none of that helps, try to confirm the complete model number and brand of the keyless for us and we will do our best to help further. The model number of the keyless should start with a 1139 prefix for most Craftsman models.

Read More
HVAC & Fireplace Bucket -
Sears Technician
July 18, 2008
A:

i have the same problem... I have Model # 13953716 Part Number 114A1136

Read More
Anonymous -
May 04, 2011
A:

Sounds like you may have the hard wired keypad. If so: To program the keypad, first unplug the garage door opener from the electrical outlet. Next, remove the nameplate from the console that the keypad plugs into and locate the program/operate switch. Flip the switch to program. Next, enter your desired four-digit PIN number into the keypad. Slide the switch back to operate and plug the garage door opener back in. The keypad should be programmed.

Read More
Don -
May 05, 2011
A:

Like the original poster, I have an older keypad which has the number "31D302 A" on the inside of the cover. It has no other identifying marks and just the word "Sears" on the outside of the front cover. It does not have an "enter" button. Can you provide instructions for reprogramming this keypad?

Read More
Steve -
December 17, 2011
A:

i have exactly this problem with the same product number. I need help on this. No answer at all?

Read More
ike -
May 23, 2013
A:

10 keys 0-9 or 12 keys 0-9 and a * and a # key? If you have 12 keys You may want to review the instructions for a TYPE 4 opener @ http://www.liftmaster.com/CatalogResourcesV3/en-us/shared/files/tucmanuals/114A3495.pdf

Read More
Anonymous -
May 23, 2013
A:

Hey Ike, See response from May 05, 2011. That is exactly how to program it.

Read More
John -
December 05, 2013
See more answers
Q:

Where can I find a replacement for my touch code lock 139.53716? 53716 Accessories Touch code lock

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Anna T -
May 20, 2013
A:

I know that it is very important to have the right information for your keypad. The wired keypads are no longer in production. The new wireless keypads will replace the wired keypads. The part number for the conversion kit for your garage door opener is 53682, and the cost is around $70.00. Just click on this link to view it: 53682 Conversion Kit. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
May 20, 2013
A:

The part you suggest is not what I am Looking for. I need a replacement number keypad for my garage door opener. any suggestions?

Read More
jeb2525 -
May 21, 2013
A:

The keypad you are trying to replace is no longer produced. In fact all manufacturers has stopped producing wired keypads. The ones that are available now are all wireless. These are programmed directly to the opener by using a radio frequency. In order to replace the old keypad with a new one, you will need a conversion kit. That is what I inculded in the link above. That conversion kit will program to any new keypad and remote. Please let me know if you need anything else. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
May 22, 2013
See more answers

Top Accessories