Model #13953637SRT1 CRAFTSMAN Garage Door Opener

  • Security & Standard Accessories
    3 Results
  • Hardware/extension Kits/bulbs
    3 Results
  • Rail Assembly
    3 Results
  • Installation Parts
    3 Results
  • Opener Assembly
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

i have 2 139.53637srt 1/2 hp garage door openers. bothe were manufactured 7/1994. over time have lost/misplaced keyless remotes. openers are programmed into car

A:

Hi,

Thanks for contacting  ManageMyLife.  I understand how frustrating it is having trouble with your appliance.

It sounds like all the slots have been filled on the opener.

I would suggest that you erase the memory on the logic board and then try to reprogram the remotes.

Yes, there are dip switches on the remotes but the receiver does not on this model. This receiver is called a smart receiver and as long as you have the dip switches set the same on all the remotes it should work.

I am waiting for the factory to tell me the operating frequency of this control. 

I will send the instructions for programming the remotes in the images below.

Here is the link for you old GDO manual.   

If you decide to have a Technician check your appliance, call this number to get the service call arranged 1-888-266-6317.

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Bill

Read More
Bill__W -
Sears Technician
November 07, 2013
Q:

Garage door repair

A:

The Managemylife web site is a good resource to find out what may be happening with your Garage Door Opener. I did some research for you at Managemylife.com and found an excellent article that also has multiple expert answers at the bottom of the web page that addresses the most common questions that have been asked by other members. I hope this will help until your expert can answer your specific question. I attached the link below.

Read More
Alina -
January 03, 2013
A:

I can understand how frustrating this problem would be after having repairs done. Does the LED illuminate on the overhead unit? If so, does it flash when trying to operate? The number of flashes are a diagnostic code. You indicated you have checked the outlet for power. Do you hear the motor clicking or humming? If there is no response, it may be the motor or the logic board in the unit. Unplug the opener, remove the cover and check the wiring harness to the logic board. Make sure it is making full contact. Check the logic board for any burned spots or cracks. Please reply with additional details. I will be happy to help. Thank you for using Manage My Life.

Read More
Barbara H. -
Sears Technician
January 05, 2013
A:

I have a manual lift garage door and the wires broke and need to be replaced. There is a bracket that attaches somewhere ( I suspect on frame). Is there a standard diagram or shetch which shows standard mounting for bracket as well as how lift wires are mounted on springs and sockets?

Read More
Ken -
October 08, 2013
A:

Hi Ken. You will need the model number of the garage door for information and parts. The manual may be available for your model by entering the number in the search box at Manage My Life Manuals .

Read More
Barbara H. -
Sears Technician
October 10, 2013
See more answers
Q:

SRT error code 5 light blink sequence

A:

Error codes mean so many different things so when an error code comes up it can be really frustrating. While you are waiting on an expert to answer your question, I found a great link in the ManageMyLife website. Click here. Hope this helps!

Read More
Dezeray S -
July 17, 2013
A:

Tom, for some reason everyone gets messed up with the 5 flash code. the 5 flash code is the RPM sensor or the motor overheated. unplug the opener for 30 min. then plug it back in and try it. if the door moves 6-8 inches and stops the rpm sensor will be the issue. either the sensor went bad or the cup came loose on the motor shaft and needs pushed back on as far as it will go. or if the door does not move at all and just clicks the logic board is at fault by reading a motor over heated issue and needs replaced because the motor rarely ever fails and with the power unplugged for 30 min if the motor was overheated it would be cooled down in the 30 min so it will revert back to the logic board is bad. repeated opening and closing of the opener for testing or adjusting will over heat the motor and go into thermal shut down and give you the 5 flash code.

Read More
TC -
July 18, 2013
A:

I can definitely understand your concern in having a properly working opener, I will be glad to assist you today. The 5 blinks of the led tells you the problem is in the rpm sensor in the motor unit of the garage door opener. I do recommend resetting it by unplugging the unit. ( Note: Be careful when going to main unit on top, will need a second pair of hands. ) You can go to: Sears Parts Direct  and see a parts diagram of your garage door opener. There is a black plastic interrupter cup mounted on the end of the motor shaft. Be sure this cup is pushed on the shaft as far as it will go. The notched edge of the interrupter cup rides inside a groove of the rpm sensor and breaks an infra red beam as it turns. If it isn't breaking the beam the rpm sensor doesn't work. If the interrupter cup is riding as deep in the groove as it should, you need to replace the rpm sensor. I am sending you an image showing what the flash codes mean for the garage door opener. Hope this helps, Thank you for choosing Manage My Life.com.

Read More
Maira -
Sears Technician
July 18, 2013
A:

Tom, see what I mean about the 5 flashes, the expert never says anything about the 5 flashes except for the RPM sensor. but you can read it for yourself if the door opener does not move replace the logic board.

Read More
TC -
July 18, 2013
See more answers

Top Parts

Top Accessories