Model #13500 HONEYWELL Air Cleaner

  • Air Cleaner
    3 Results
Find part by diagram >

Question and Answers

Q:

Wheels keep stripping on mower drive.

A:

Having to order the right parts for an appliance can be frustrating, but yet is also very important to order the proper parts for repair. While you waiting for an expert to reply I recommend visiting the sears parts direct website were you can find a parts list and diagram for your model. I have attached the link below.

Read More
Priscilla V -
July 05, 2011
A:

That is exactly what I did, I ordered it from the part direct website and from a live human. Both sets stripped the plastic inside of the wheel.

Read More
David -
July 06, 2011
A:

whats the brand of mower you have. .sounds like a self propelled craftsman mower with what you are saying . many models of self propelled mowers do have specific sets of wheels that will work the way it should allowing the gear drive to engage without stripping your wheels. height and widness of the tire has to match the gear drive or they wont work properly i have seen many mowers and repaired many with the same issue your having now. lawnboys,yardmachines sometimes craftsman does have the same kind of an issue so that is why i was asking what brand do you have

Read More
Anonymous -
July 06, 2011
A:

This a Craftsman mower. And after ordering so many sets of drive wheels I'm not going to spend any more money on it till I get some answers on why the previous sets of wheels didn't work. If you order the way I have and receive the same results you reach the point of Hum does Craftsman or Sear know anything about this?? Do they care? I wonder what happened to satisfaction guarantied. You know it wouldn't be near as hard to deal with this problem except I have purchased the same mower for my son and his works fine. Same age zero wheel replacement.

Read More
David -
July 07, 2011
A:

if your son has the same mower maybe you can take the wheel measurements off his and compare them to what you have. see if yours are bigger,smalller, or the same if they are the same the next thing i would check is to see if your gear drive is also the same lenght or if it has a adjuster on it to match up with your wheels because i agree that is to many sets of wheels in such a short time for them to go bad as quickly as they do. let me know what you find out. i would really like to help you solve this issue as i said before i have repaired, replaced wheels,gear drives,never had them brought back to me after i fixed them if you find any diffrences let me know maybe i will be able to help you trouble shoot the problem .good luck hope this helps you solve your problem.

Read More
john -
July 07, 2011
A:

The correct part number for the front wheels on your mower is 407755X460. If this is what you have been getting, they are correct.

There is a kit for a problem with the front wheels locking up or not driving. This kit includes new spacer washers, wheel adjusters, and pinion gears for both sides of the mower. You will need to order the wheels separately. The part number of the repair kit is 422109 and the price is $40.99.

I recommend you call 1-800-469-4663 and tell an agent there about the problem with your mower. It is possible the repair on the mower might be no charge to you.

I believe this kit will solve the problem on the mower.

Read More
Jimmy K -
Sears Technician
July 07, 2011
A:

Ok Jimmy K, I spent 20 minutes on the phone today(07/11/11) with the folks at the 800# you provided. The part #422109 is the level adjuster ( this raises and lowers the cutting deck). It has nothing to do with the problem my mower has with stripping the front wheels. The people at this number could not help with anything. They did want to order the wheels with the other number you provided but unless I am confident that the problem with the wheels is fixed I'm not going to pay for any more parts. Any other ideas?

Read More
David -
July 11, 2011
A:

David, I apologize for the hassle of using the 800 number. The reason I suggested the wheel adjuster is because the axle for the wheel is on it. This kit was developed for some mowers that were failing to drive at times. The axle for the wheel might have been out of position on some wheel adjusters. I think the best thing to do is to take the mower to a Sears Service Center for repair. When you drop it off be sure the information about replacing the wheels numerous times is noted. You will be given an estimate before any work is done. I think the technician will recognize the problem and take care of the problem.

Read More
Jimmy K -
Sears Technician
July 12, 2011
A:

Jimmy, when I went to the sears parts dept. here in San Antonio, they told me the mower had to be shipped off to somewhere and there was a non refundable deposit of $135.00 to send it off. All this really turned me off. I find it hard to believe that in a city the size of San Antonio there is no service center anymore. What do you suggest?

Read More
David -
July 12, 2011
A:

Any answers on this?

Read More
David -
July 15, 2011
See more answers
Q:

Zigzag Stitch 158.13500

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your sewing machine and I do understand your frustration. Glad to help out. I'm looking at your model number 158.13500 and here is a link that may help with additional troubleshooting. I would suspect and issue with the foot since all other functions work. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
January 06, 2015
Q:

My Maytag dryer (Model # MDE3758AYW) - Motor drive pulley broke. What is part #? (Not on your drawings)

A:

The motor drive pulley for your dryer is not a replaceable part. It is probably pressed on the motor shaft. You will have to buy the motor to get a new pulley. The motor part number is 2200376 and the cost is around $135.00.

Read More
Jimmy K -
Sears Technician
August 07, 2008
A:

Actually, I found out buy doing my own search of your own database (note that I am not "the expert") that the drive pulley part number for my dryer is 31001535 (good for all seriese-10 Maytag Dryers). No, the pulley does not press on - it screws on with a counter-clockwise thread and No you do not have to buy a new motor to obtain the pulley - it costs only $5.95. Wrong on absolutley all accounts!

Read More
ScottMS -
August 07, 2008
A:

Got the pulley and put it on the dryer - Works perfectly for $5.95 NOT $135.00! The replacement pulley is made of steel whereas the orrigial was die-cast zinc. Obviously this Maytag dryer was made with inferior parts and only lasted 1 1/2 years. I'm suprised Sears sells such junk AND DOESN'T STAND BEHIND IT!

Read More
ScottMS -
August 14, 2008
A:

Got the pulley and put it on the dryer - Works perfectly for $5.95 NOT $135.00! The replacement pulley is made of steel whereas the orrigial was die-cast zinc. Obviously this Maytag dryer was made with inferior parts and only lasted 1 1/2 years. I'm suprised Sears sells such junk AND DOESN'T STAND BEHIND IT!

Read More
ScottMS -
August 14, 2008
A:

Hey Scott - Thanks for doing the legwork on this one! My idler pulley disintegrated and the belt jammed. Turned out the belt was stronger than the cheap zinc motor pulley which promptly screwed itself right past the threads and onto the motor shaft. Needless to say, I had to cut the old pulley off with a hacksaw. Not pretty. I found the 754305 pn stamped inside the rim and googled it and found your post here. Way to out-expert the experts man! And thanks again. You just made my life a little easier!

Read More
Andy -
June 23, 2012
A:

Hey Scott, you may not see this anytime soon, but I am having the exact same problem. You said you fixed it but you didn't say where you ordered that pulley from. Help!

Read More
Evan -
February 04, 2013
A:

Hello Evan. I am not the same expert that originally answered this question. I see that Scott did some good work and found that pulley. You can order that part (31001535) from this page: Motor Pulley . You may also be able to find it locally. I hope that this helps. If you need more assistance, let us know.

Read More
Lyle W -
Sears Technician
February 05, 2013
See more answers