Model #1269 PEERLESS Faucet

  • Two Handle Washerless Tub And Shower Valves
    3 Results
Find part by diagram >

Question and Answers

Q:

Removing the old starter 42A707-1269-01 Briggs&stratton Engine

A:

Thank You for choosing Sears PartsDirect.com. I regret to hear that you are having issues with your mower and do understand your frustration. Glad to help out. Im looking at your model number 917256571 and to replace the starter you have to remove the blower housing on the top of the engine. Once the blower housing is removed there are two different ways to replace the starter. The first is to remove the flywheel to expose the starter bolts. To remove the flywheel you need to remove the large nut securing it. Then use a flywheel puller to pop the flywheel loose. The other way to remove the starter is reach under the flywheel with a 1/2 inch wrench. Use the wrench to remove bolts then slide the starter out from under the flywheel. This method takes a little more time but does not require any special tools.Here is a video that may help.

Please let me know if you need further assistance on the engine repair.

Here is a link to order any parts you need. Sears Parts Direct .

 

 

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website:Sears Home Services .

Read More
Sherman_G_Wallace -
Sears Technician
April 14, 2014
Q:

Tractor blades won't disengage

A:

Thank you for your question.

 

 

 

I am sorry you are having a problem with the tractor. Wow, you have done all the checks I would have recommended. I think you are correct that the clutch has failed. To be one hundred percent sure the clutch is the problem you can disconnect the wires from the back of the PTO switch. Then see if the blades turn when the engine runs. If it does, I recommend replacing the clutch. If you need to order the clutch, you can do so from the following link. Replacement electric clutch for a Craftsman tractor model number 917.250551.   

 

 

Please let me know if you need further assistance on the repair of the mower.

 

 

 

Thank you for using Manage my life.

 

Mark T.

Read More
Mark T -
Sears Technician
October 09, 2013
A:

Thank you for your help.

Read More
George -
October 09, 2013
See more answers
Q:

Tub gasket doesn't seem to fit

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Alina -
March 23, 2013
A:

 

Thank you for your question and I understand your concern.

Thank you for adding the image.  It is not abnormal for the two ends of the door gasket to not meet in the middle. This is normal. There is a baffle seal located between the inner and outer door that will mate to the front of the tub that will prevent any water from leaking. The door seal is not designed to meet in the middle to allow for venting.

If it continues to leak after replacing the door seal, check and make sure the baffle seal is matting up against the lower front edge of the tub.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

 

Read More
Joey S -
Sears Technician
March 25, 2013
A:

Thanks so much, Joey S. This is indeed helpful. Can you give me some idea of what the baffle seal looks like?

Read More
K -
March 25, 2013
A:

K; I added an image below and I circled the baffle seal. If the image is not there, You can copy and past the URL below in your browser and see the same image. http://www.searspartsdirect.com/partsdirect/part-model/Tappan-Parts/Dishwasher-Parts/Model-TDB652RBR0/1269/0130000/Y6003205/00004?blt=06&prst=0&shdMod=TDB652RBR0

Read More
Joey S -
Sears Technician
March 25, 2013
A:

Thanks again!

Read More
K -
March 25, 2013
See more answers