Model #1230 PEERLESS Faucet

  • Single Handle Washerless Tub And Shower Valves
    3 Results
Find part by diagram >

Question and Answers

Q:

Warranty khmc1857Bss-0

A:

Hello,

The phone number to reach our office for the protection agreements is 1-800-827-6655.  They should be able to assist you in confirming that your range hood has warranty coverage. 

If you need to reach out to KitchenAid for the manufactures warranty they can be reached at
1-800-422-1230.

Let me know if you have any other questions!

Alicia

Read More
Alicia9259 -
Sears Technician
August 27, 2015
Q:

Does Control panel come with module?

A:

Error codes can be an inconvenience and keep your range from working properly. I did some research and I was able to find a link with a similar question. I am also adding a second link in where you can find help in finding the correct parts. I hope this helps with your research while you wait for your expert response.

Read More
Joseph P. -
January 03, 2013
A:

Apologies but the error code was NOT F12 but F1E2. Thanks Paul Morrill

Read More
Paul -
January 03, 2013
A:

Thank you for your question and I understand your concern.

The "F1 E2" indicates a loss of communication between the power board and display board. If there are no loose/dirty or disconnected wires between the two, It will be impossible to know which one is faulty. I strongly suggest calling a service technician to diagnose or make that decision.

  • FO E0 No fault found. No fault found. No action required.
*F1 E2 Power board communication. Lost communication with power board. Check communication between power board and display board.
  • F1 E3 Configuration mis-match. Configuration jumper change; freestanding, electric switches or P3 pins 3 to 7 changed since power up.
  • F1 E4 Oven sensor calibration. Oven sensor not calibrated. Run calibration routine.
  • F1 E5 Meat probe calibration. Meat probe not calibrated. Run calibration routine.
  • F1 E6 Display board. Display board EPROM access. Replace display board.
  • F1 E7 Power board E2. Power board EPROM access. Replace power board.
  • F1 E8 Power board supply lift. Improper keypad feeding. Replace power board.
  • F1 E9 Keyboard gain. Unstable keyboard gain. Replace display board.
  • F1 EA Stack warning. Exceeded stack warning level. Reset power. If problem persists, replace power board.
  • F2 E0 Keypad disconnect. User is cleaning too long or keypad is disconnected. 1. Check keypad connections. 2. If problem persists, clean switch surface.
  • F2 E1 Cancel key. Cancel key invalid. Needs surface cleaning.
  • F2 E3 Keypad spill. Key held down too long or keyboard short or spill on switch surface. Needs surface cleaning.
  • F3 E0 Open oven sensor. Oven sensor open. Replace oven sensor.
  • F3 E3 Shorted oven sensor. Shorted oven sensor. Replace oven sensor.
  • F3 E4 Oven temperature too high. Oven temperature too high (runaway). Replace oven sensor, or control.
  • F4 E0 Shorted meat probe. Meat probe shorted (less than 1500 ohms). Replace meat probe.
  • F5 E1 Self clean latch. Self clean latch not locking. Check latch system.
  • F5 E5 Clean temperature. Self clean temperature not achieved after 30 minutes. Check door hinge and door seal gasket.
  • F5 E7 Clean unlatch. Door unlocked but will not unlatch. Check door switch, latch switch, and rod mechanism.
  • F7 E0 Latch switch. Invalid latch switch reading. Check latch switch.
  • F7 E1 Door switch. Invalid door switch reading. Check door switch.
PF Power Failure (Not a Failure Mode) Push CANCEL. (Do not replace control.)

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 05, 2013
A:

Hello Joey, thanks for the response back to this. I will not be able to get a technician to look at this easily since the stove is now in my house in the Caribbean. What I need to know. 1. Are the two boards you are talking about above (power board and display board, the two part numbers I put in my original posting? 2. Does the 9 series board have this extra module already installed on the board if I order it? This is very important and will not work on my stove without this module. A quick response would be greatly appreciated. Thank You.

Read More
Paul -
January 08, 2013
A:

Paul: I see only three components. The touch panel, display board and the power board. The display board is part #8184718 and the power board is part #9754378. The touch panel is offered in only one color and the part # is 9754341CB. I do not have parts here to physically check. I recommend calling Kitchen Aide/Whirpool for part verification for your model. Call the KitchenAid Customer Interaction Center toll free: 1-800-422-1230.

Read More
Joey S -
Sears Technician
January 09, 2013
A:

Hello Joey, not sure if you are still around in this conversation. But further to this thread, I bought a new Power/Computer board for the stove that did not fix the problem. The F1E2 error code still persists. I have not bought a new display board and is being delivered now. My question is if you install a new power/computer board is there an input code that is needed for the stove to recognise that new board? Second question is it likely that this display board new is going to fix this problem? I have now spent close to $600 fixing this issue on essentially a brand new stove. I have read on several posts that this is a very well known issue with these stoves is there a way to prevent it happening again moving forward? Many thanks, Paul

Read More
Paul -
December 27, 2014
A:

The error codes should display with a letter "F" followed by a number and then another letter "E" followed by another number. An example of an error code would display as F0 E0, F1 E2, F1 E4 etc. Please reply with the correct fault code for specific information.

Read More
Joey S -
Sears Technician
December 29, 2014
See more answers
Q:

I have a wall oven Kenmore Model 91130469792, that has a code of F7. What does F7 mean?

A:

The F7 is telling you there is a failure in the touchpad. You should turn the power off to the oven for 1-2 minutes and see if it comes back.

If it comes back you can turn the power off and remove the control panel. Disconnect the ribbon connector from the control panel to the clock and inspect it for damage or breakage. Plug it in firmly and try the oven again.

If the F7 returns you need to replace the control panel. The parts list shows 2 control panels, one white and one black. I am sending you the part numbers and prices of the control panel.

WB36T10540 PANEL CONTROL WHITE 227.99 WB36T10541 PANEL CONTROL BLACK 222.49

Read More
Jimmy K -
Sears Technician
August 05, 2008
A:

I turned the oven breaker switch off earlier, about 20min. I turn the breaker back on and reset the clock and it is working so far. The key pad responds to commands now and the code F7, doesn't come on. Thank for the help

Read More
Daniel -
July 15, 2011
A:

oops? oven started giving me the F7 code and key pad does not response. I will try the next step, disconnect ribbon and or order a control.

Read More
Daniel -
July 15, 2011
A:

My oven also starts beeping at all hours of the day or night along with this code. Currently the oven door is open but stuck in the locked position. I am trying to figure out how to fix that also. As far as the beeping I have to take the facing off of the control panel and disconnect one black wire for about 30 seconds to make it stop. Sometimes I have to repeat this procedure to make the beeping stop.

Read More
Rudy -
March 24, 2014
See more answers