Model #11652813203 KENMORE Attachments (Vacuum)

  • Power-mate
    3 Results
Find part by diagram >

Question and Answers

Q:

How to replace canister vacuum swivel? 11652813203 Kenmore P0wer-mate

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your vacuum and I do understand your frustration. Glad to help out. I'm looking at your model number 11652813203 and click here for the service manual instructions. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

 

Read More
Sherman_G_Wallace -
Sears Technician
January 27, 2015
Q:

KENMORE, Model # 11652813203 Number: KC92PCREZ000 is this a part that a typical homeowner could install? If so are there instructions?

A:

This is for a Kenmore vacuum cleaner

Read More
Richard -
March 18, 2011
A:

Managemylife.com is a great place to find help. I'm sorry about the difficulties that you are experiencing with your Kenmore vacuum cleaner. I did some research at managemylife.com and found an expert answer to a similar question that may assist you until your expert can respond. I have attached the link below. I hope this helps.

Read More
James -
March 18, 2011
A:

This is not a part I'd suggest you try to replace yourself. The best option to repair this is to have it done in the shop.

If you do not feel confident repairing this problem yourself, then you can have it repaired by a Sears�s technician. Here is a link that will provide the nearest drop-off locations: Sears Home Services .

There is no step by step available to help with this project.

The repair would be $59.99 flat rate and is worth it.

Read More
Fred M -
Sears Technician
March 19, 2011
A:

Thanks for the information. I have saved the $59,99 by going ahead and doing it myself. It really was not too difficult. Just needed to be careful not to damage the parts I needed to take off the old part and carefully observe how everything came apart so I could put it together correctly. It took about 30 minutes. The part only cost $25.16 + tax.

Read More
Richard -
March 19, 2011
A:

Great job. Glad to hear it all worked out.

Read More
Fred M -
Sears Technician
March 19, 2011
See more answers
Q:

Vacuum carpet option does not work

A:

I understand your concern toward wanting to make sure that your vacuum cleaner is working properly so that your rug will be nice and clean. While you are waiting for an expert answer, I suggest you look in your owners manual in the troubleshooting pages. Below is a link in where you can enter your model number and your owners manual will pop up. I am also adding a second link in where you also enter your model number and a parts list diagram will pop up. I hope my links are useful.

Read More
Joseph P. -
January 05, 2011
A:

Thanks, but this did not help. I have the part numbers. I just need to know if I must order the complete parts of if there are smaller parts I can order. Thanks.

Read More
_pags_ny789 -
January 05, 2011
A:

To repair the connector on the wand, you have to replace the wand. You can replace the connector on the power mate by replacing the wire harness.

The parts you will need are:

20 116 8175252 1 $29.39 LEAD WIRE, "A" UNIT 20 116 8192120 1 $79.61 WAND, EXTENSION (INCLUDES ILLUS 5)

If you are not comfortable repairing the vacuum, you can take it to Sears. Go to http://services.sears.com/shs/category/repair?sid=MMLxexpertxmerch to find the nearest location.

Read More
Jimmy K -
Sears Technician
January 07, 2011
A:

Jimmy, Thanks for the helpful reply. I don't see the connector on the power mate or its part number in the "hose and attachments" box on the parts diagram for this model vacuum. Are they not shown? Should I order it anyway? Also, looks like I must replace the entire wand, even though it is only the 2 electrical receptacles that are worn. Thanks, Michael

Read More
_pags_ny789 -
January 08, 2011
A:

Terry, you can't get the connectors on the wand without replacing the complete wand. The part numbers I sent are from the parts diagram of the power mate. To see the parts diagram of the power mate go to [www.partsdirect.com?sid=MMLxexpertxmerch] and enter model number 116.52813203. I should have sent you this information in the first reply. I apologize.

Read More
Jimmy K -
Sears Technician
January 10, 2011
A:

Thanks. I think I figured it out. I will order the parts you listed.

Read More
_pags_ny789 -
January 10, 2011
A:

Hello, I received the parts and installed the wand. The carpet feature now works! But I still have a problem. The connector cable is for the power mate. I need the female connectors on the swivel assembly as I noted in my first post. Must I replace the entire swivel assembly, or is there just an electrical component I could replace? Thanks

Read More
_pags_ny789 -
January 22, 2011
A:

Go to [www.partsdirect.com?sid=MMLxexpertxmerch] and look at the parts diagram for the vacuum. Search model 116.22813203 and look on the "hose and attachments" page. I think you will need item 2. The rubber part on the end of your old hose is called a hose adapter. The adapter has a slightly raised molded joint on it. Place a small screwdriver at each end of the molded joint and push it underneath the joint 1- 1 1/2 inches. These screwdrivers will release a tab underneath the molded joint and the hose adapter will slide off the hose. You will need to perform this operation to both of the hose adapters. The hose adapters will slide on to the new hose and lock without you having to use the screwdrivers I hope this helps.

Read More
Jimmy K -
Sears Technician
January 24, 2011
See more answers

Top Parts