Model #11632920200 KENMORE Vacuum, Upright

  • Nozzle
    3 Results
  • Agitator And Endcap Assembly
    3 Results
  • Agitator Motor And Gear Assembly
    3 Results
  • Dust Compartment And Motor
    3 Results
  • Hose And Attachment
    3 Results
Find part by diagram >

Question and Answers

Q:

How do I remove the handle on my vac #11632920

A:

Vacuums are put together so neatly, it can be hard to figure out how to get one apart. While you wait for the expert, you can view the schematics at Sears Parts Direct. It gives an exploded view, just scrollover image. I also added the link to your owner's manual. They often have diagrams. http://www.searspartsdirect.com/partsdirect/part-model/Kenmore-Parts/Vacuum-Parts/Model-11632920200/0582/0645000/P0209087/00004?blt=06&prst=&shdMod= http://www.managemylife.com/mmh/owner_manuals/11845/KENMORE-Vacuum-Upright-L0810050?brand_name_search=11632920

Read More
Barbara H. -
November 07, 2010
A:

Thank you for your question.

I can understand wanting to know how to get to the on/off switch.

  • I will send some instructions and a picture with the instructions.

I hope this will help with your switch repair.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
November 08, 2010
A:

i took all the screw out as you suggested but the Auto Reverse Handle still won't pull off. I can't get to the on/off switch with the handle on . Even the Handle Locking Button will not move .

Read More
BARGAIN MAN -
November 08, 2010
A:

I am sorry I thought I gave you all the instruction pictures. If you follow these instructions you should be able to get to the switch for replacement.

Read More
Sam A -
Sears Technician
November 09, 2010
A:

I understand what you are saying but prying the handle apart seems impossible. I have used three different flat screw drivers and it is not coming off. There must be latches inside preventing it. There must be a easier way of getting it off . I don't want to break it. I tried prying from the sides ends and every which way . Almost ready to dump it , unless someone has a better way of getting the handles apart.

Read More
BARGAIN MAN -
November 09, 2010
A:

Finally got the two parts of the handle apart gently. Guess what the two tabs of one side of the handle that holds it together broke off. I person would wonder if it was made so they would break. Now what . Even though it is a older vacumn would you think the mfg. would honor the part?

Read More
BARGAIN MAN -
November 09, 2010
A:

Thanks Sam I had to pry the handle apart , and broke the latch but there was no other way to get it off. Thanks for you help .

Read More
BARGAIN MAN -
November 09, 2010
See more answers
Q:

I need to know where the switches belong in my vacuum cleaner 116.32920200

A:

Okay, I figured out the switches. Now there is a spring in the handle. I do not know where this goes. Any help would be appreciated.

Read More
hmtaylor -
May 19, 2010
A:

The information in the image below should help you reassemble the handle properly. Wire management is extremely important in this vacuum cleaner. Failure to properly route the wires can result in one being pinched and then shorting. If you are not able to reassemble the handle using the information provided below, I recommend that you carry the vacuum cleaner into a Sears Repair Center and have it fixed by a technician. Here is a link for the Sears Service website that has information on drop-off locations and service labor rates: Sears Home Services .

Read More
Lyle W -
Sears Technician
May 20, 2010
A:

Yes!! This is perfect. My vacuum cleaner is back in service. May I have this exploded view schematic for all the components of this vacuum cleaner? Thank you, Heidi

Read More
hmtaylor -
May 22, 2010
See more answers
Q:

how do i install the the sliding knob/pin / spring in my vacuum extension rod for model 116.28614801 /116.28615801

A:

The image below should help you open up the handle and install the sliding knob in the handle of your vacuum cleaner. Your model may not look exactly like the one shown but the access procedure should be about the same. Be sure that the vacuum cleaner is unplugged before accessing the switch in the handle.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
April 28, 2010
A:

I need something like this diagram for my vacuum cleaner, Sears 116.32920200. I had to replace the handle. The wiring is inside the handle. I would like to verify the position of all the switches and the location of a spring that fell out. Any help would be appreciated, Heidi

Read More
hmtaylor -
May 19, 2010
A:

I figured out the switches!! Now I need help with the spring (PN: 8192428) in the handle. I do not see where this spring goes in the handle. Please help!! Thank you, Heidi

Read More
hmtaylor -
May 19, 2010
See more answers

Top Parts