Model #11625915500 KENMORE Vacuum, Canister

  • Canopy/body/motor
    3 Results
  • Attachments
    3 Results
  • Hose
    3 Results
  • Cord Reel
    3 Results
Find part by diagram >

Question and Answers

Q:

User Manual Power Mate, Jr model #116.C85PBPK0V022 116.C85PBPK0V022

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your vacuum. Upon researching model C85PBPK0V022: I apologize for any inconveniences, at this time we do not have the owner’s manual for the power mate jr available as a PDF.  

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
June 10, 2015
A:

Pardon my confusion but I received an email that my inquiry had been answered. Additionally the forum itself reflects that an Expert has responded, yet, as you can see, once the question is fully expanded no answer can be found. Please advise.

Read More
Sue -
June 10, 2015
A:

Well, I guess you may disregard my reply. Only after sending a reply did the answer appear. No disrespect intended toward the Experts on this forum, but I am not a happy camper and Sears just lost a longstanding customer of 40 years. I hope Corporate takes pleasure in the $8K I spent on all of my Kitchen appliances (Kenmore Elite) because it will be the very last dime I spend at Sears. All over their need to charge for a user manual.

Read More
Sue -
June 10, 2015
See more answers
Q:

change the wheel on my powermate

A:

Step by step instructions help with home repairs on vacuums. While you wait for the expert response, I did attach the owner's manuals with the diagrams they contain and a similar question for the hose part. The links are attached below. I hope these help.

Read More
Barbara H. -
July 05, 2012
A:

Thank you for your question on the replacement of the wheel on the power mate.

The wheel just pops off the base of the unit.

Since you are replacing the wheel you can use a large flat blades screw driver to pry the wheel out of the base.

The new wheel has plastic tabs and as you pushes it into the wheel socket on the base it should pop and lock into place.

To replace the hose swivel on the canister hose you will need to have a couple of tools to help you do this replacement.

116.2 vacuum cleaner hose elbow swivel replacement.

To replace this connection pipe you will need to have some basic tools.

  • Two small pocket type flat blade screwdrivers seam to work the best for this repair.

  • Locate on the hose elbow connection the molded seam line in the cuff and on the elbow connection.

  • Place the flat blade screwdriver in the gap between the elbow and the hose cuff and work up under the cuff along the seam line up the hose in under the cuff for about 1 inch or until you release the locking tab.

  • Do this on both sides of the cuff, so both sides are released at the same time.

  • Once the tabs are released, slide the cuff up the hose and out of the way.

  • This will expose the wiring harness on the connection pipe. NOTE: the location of the wires and how they fit onto and around the connection pipe so you can install them back exactly as they are or the cuff with not lock back onto the connection pipe.

  • Remove the push in connectors on the wire harness and then locate locking tab on the connector pipe and release it from the spiral of the hose and remove the connection pipe from the hose.

  • Install the new connector and re-connect all the wires and slide the cuff back up the connector. This will take a little working back and forth of the cuff to get it to lock onto the new pipe.

I will include a picture to help you with the repair.

I hope this helps. I am sorry but I do not have a video to offer you at this time.

Sam A.

Read More
Sam A -
Sears Technician
July 09, 2012
See more answers

Top Parts