Model #11625615506 KENMORE Vacuum, Canister

  • Canister
    3 Results
  • Attachments
    3 Results
  • Hose
    3 Results
  • Cord Reel
    3 Results
Find part by diagram >

Question and Answers

Q:

Instruct/help: Remove & replace CNSTR VAC SWIVEL CONNECTOR on hose 11625615506 Kenmore Canister vac

A:

Model: Kenmore Progressive Canister Vacuum 116 256 15506 > (Similar model numbers have the same hose.) PART: CANISTER VACUUM SWIVEL CONNECTOR [Part # KC92PBZTZV06] I have the same failure. Before I toss the whole thing I am looking for any info on replacing this swivel. Method of disassembly is not obvious. Is there a non-destructive way to get it apart?

Read More
BOB -
December 16, 2015
Q:

Replace Vacuum Hose

A:

When it comes to replacing parts on the Vacuum can be challenging. I have taken the time to research on the Manage My Life website and have located similar information towards your question. While you are waiting for a detailed reply from an expert I have attached the links below. Hope this helps!

Read More
Priscilla V -
March 07, 2012
A:

Thank you for your question. Thank you for the model number. I can understand wanting to replace the swivel yourself. You will need some basic tools. Two small pocket sized flat bladed screw drivers seem to work the best. I will send you some pictures on how to change the swivel.

  • Remove the swivel and hose from the vacuum.
  • At the swivel end look for the plastic mold lines on both the rubber cuff and the elbow of the swivel.
  • Once you locate those insert your flat bladed screw drivers into the swivel groove at the mold seam lines and pry under the cuff and slide the screw driver back under the cuff about 1 1/2 inches to release the locking tab for the cuff on both sides of the swivel.
  • Once you have this done you should be able to slide the cuff up the hose and expose the wire harness and how they lay in the holders. Make note of the wire harness routing so you can install them the same way on the new swivel assembly.
If you do not get them correctly, the cuff will be very difficult to get to slide up and lock.
  • You will now see the locking tab on the swivel that hooks onto the corrugated hose, Flex to release and remove the swivel from the hose.
Re-assemble in reverse order.

The Third image gives the basic steps for taking the handle apart. Your model might be slightly different but the steps are the same. Once you have the handle apart insert the hose wires into the connector and properly route them in the holders before reassembly. I hope this is helpful. Please reply below if you need further assistance on installing the hose. Thank you for using Manage My Life.

Mark T.

Read More
Mark T -
Sears Technician
March 07, 2012
A:

Thank you for your question. Thank you for the model number. I can understand wanting to replace the swivel yourself. You will need some basic tools. Two small pocket sized flat bladed screw drivers seem to work the best. I will send you some pictures on how to change the swivel.

  • Remove the swivel and hose from the vacuum.
  • At the swivel end look for the plastic mold lines on both the rubber cuff and the elbow of the swivel.
  • Once you locate those insert your flat bladed screw drivers into the swivel groove at the mold seam lines and pry under the cuff and slide the screw driver back under the cuff about 1 1/2 inches to release the locking tab for the cuff on both sides of the swivel.
  • Once you have this done you should be able to slide the cuff up the hose and expose the wire harness and how they lay in the holders. Make note of the wire harness routing so you can install them the same way on the new swivel assembly.
If you do not get them correctly, the cuff will be very difficult to get to slide up and lock.
  • You will now see the locking tab on the swivel that hooks onto the corrugated hose, Flex to release and remove the swivel from the hose.
Re-assemble in reverse order.

The Third image gives the basic steps for taking the handle apart. Your model might be slightly different but the steps are the same. Once you have the handle apart insert the hose wires into the connector and properly route them in the holders before reassembly. I hope this is helpful. Please reply below if you need further assistance on installing the hose. Thank you for using Manage My Life.

Mark T.

Read More
Mark T -
Sears Technician
March 07, 2012
A:

I just asked the same question. There's no need to repeat the answer. Could you kindly just send the pictures to my e-mail address? The images on the preceding questions don't enlarge on my laptop. Many thanks..

Read More
Aaron -
September 16, 2015
See more answers
Q:

What is the size of my Kenmore washer, 70 Series model 110.82874120? 110.82874120

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your washer. Upon researching model 11625615506; based on the model number provided, this model dimensions are Length: 2F7.8 , 2F3.0, Height 3F1.4.

  I trust this information will help you, we appreciate your business thank for choosing Sears.

 

Read More
CarlosZ -
Sears Technician
April 14, 2015

Top Parts