Model #11622613205 KENMORE Vacuum, Canister

  • Base/body/dust Box
    3 Results
  • Hose And Attachment
    3 Results
  • Power Cord Reel
    3 Results
  • Tool Caddy
    3 Results
Find part by diagram >

Question and Answers

Q:

I replaced the swivel on my 11622613205 vacuum. I connected wires (y-y, w-w, b-b). It doesn't work. Can you help?

A:

The connections y-y, w-w, b-b, are correct. A wire might have gotten disconnected from the switch or motor in assembly.

I am sending you a wiring schematic for the vacuum. If we can help, send another email.

Read More
Jimmy K -
Sears Technician
October 21, 2009
A:

I'm having the same issue. I replaced the swivel but the vacuum doesn't turn on. Is it possible to get the wiring schematic with more resolution? I can't see the details on the wiring schematic that was posted. Any other suggestion would be appreciated.

Read More
Craig -
December 04, 2014
See more answers
Q:

Kenmore Canister Vacuum model 11622613205 how to remove & install cord reel part 8192047?

A:

Having to work on your Vacuum can be quite a project. I have taken the time to research on the Manage My Life website and have located a link similar to your issue. While you are waiting for a detailed reply from an expert I have attached the link below.

Read More
Priscilla V -
October 04, 2011
A:

Thank you for your question on replacing the power cord and contact set.

Please make sure the cord is unplugged from the outlet.

First remove the top cover off the tools.

Then remove the bag cover.

Then remove the filter cover on top of the motor canopy.

The removal of these covers should expose four Phillips head screws. Remove these screws and lift up on the motor canopy to gain access to the cord reel assembly.

Once you have the canopy off then lift up on the cord reel as it sits in the key location on the side of the motor.

Notice the white center hub as to how it fits into the slot.

Work the cord plug out of the retainer guide.

There will be two screws on the back side of the reel cord. DO NOT REMOVE THE TWO SCREWS THAT SECURE THE RECOIL SPRING HOUSING.

Please remove these two reel cord screws. One screw holds the cord and reel to the opposite half and the other screw releases the cord and contact ring set.

Separate the two half�s and then locate the retainer clip that secures the contact ring on the end of the cord and push in with your thumb while you use a small flat screwdriver you pry the contact ring out of its location.

Then rotate the cord and ring to slip through opening in the cord reel.

Install the need cord and ring contact set and snap into its location.

Assemble the two half�s and secure with the two screws.

Hold the reel cord in your hand and wind the cord onto the reel and then wind the reel at eight complete rotations or more to retention the spring.

You can test the tension for the return spring before you return it to the canister base. Have someone slowly pull out the cord and then carefully push the release roller to see if it will pull all the cord back onto the reel.

I hope these instructions will help.

Sam A.

Read More
Sam A -
Sears Technician
October 05, 2011
A:

The directions don't state if the power cord should be wound around the reel first or if , after completing the 8 turns, the power cord should be fully extended (removed). I tried fully winding the cord (got confused if the power cord is wrapped clockwise or counter clockwise).. then tried pulling the cord out... it seemed to wind the spring too much and would stop the cord half way from fully unwinding.. then tried 8 turns and just replacing the reel with the power cord already extended...it would not draw the cord in... what am I doing wrong??

Read More
bob -
October 30, 2013
See more answers
Q:

I have a kenmore vacuum cleaner model # 11622613205. The hose has many leaks so I bought a new one. How do I disassemble the old hose at the powermate end (23)?

A:

I'm sorry to hear that you are having some difficulties with your vacuum cleaner, its great that you are wanting to do some repairs on your own. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assistance for you.

Read More
Joseph P. -
December 28, 2011
A:

Thank you for your question and model number. I can understand wanting to replace the swivel yourself. You will need some basic tools. Two small pocket sized flat bladed screw drivers seem to work the best. I will send you some pictures on how to change the swivel.

  • Remove the swivel and hose from the vacuum.
  • At the swivel end look for the plastic mold lines on both the rubber cuff and the elbow of the swivel.
  • Once you locate those insert your flat bladed screw drivers into the swivel groove at the mold seam lines and pry under the cuff and slide the screw driver back under the cuff about 1 1/2 inches to release the locking tab for the cuff on both sides of the swivel.
  • Once you have this done you should be able to slide the cuff up the hose and expose the wire harness and how they lay in the holders. Make note of the wire harness routing so you can install them the same way on the new swivel assembly.
If you do not get them correct the cuff will be very difficult to get to slide up and lock.
  • You will now see the locking tab on the swivel that hooks onto the corrugated hose, Flex to release and remove the swivel from the hose.
Re-assemble in reverse order.

The third image below will aid in disassembling the handle to install it on the new hose. I hope this is helpful. If you need further assistance, please reply below with more details.

If you do not feel confident repairing this problem yourself, then you can have it repaired by a Sears technician. Here is a link that will provide the nearest drop-off locations: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
December 29, 2011
See more answers

Top Parts