Model #113299142 CRAFTSMAN Saw Table

  • Unit Housing
    3 Results
  • Motor Base Assembly
    3 Results
  • Fence Assembly
    3 Results
  • Miter Guage Assembly
    3 Results
  • Guard Assembly
    3 Results
  • Switch Box Assembly-domestic
    3 Results
  • Switch Box Assembly Supplied In Canada Only
    3 Results
  • Legs
    3 Results
  • Table Extension
    3 Results
Find part by diagram >

Question and Answers

Q:

What's included in part # 30420 arbor housing Key #55? the picture included shows it complet with bearings and pulley. Thiis is for saw model 113299142 113299142

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Barbara -
June 23, 2013
A:

Thank you for contacting SearsPartsDirect.com with your question about the arbor housing for you Craftsman Table Saw. I apologize for the confusion caused by the difference between what the parts diagram shows compared to what the photo on the website shows. I will be happy to clarify this for you.

On the Unit Housing parts diagram, key 55 came as an individual part when your table saw was first produced. And the part number at that time was 30420. However, the manufacturer has made a change to the part. The new number is 508123. That replacement part number is for an assembly that includes key 55, in addtion to keys 33, 48, 51, 52, 53, 54, 56 and 57. There are several advantages to an assembly as opposed to replacing an individual part. The assembly requires less work on your part because the assembly is already put together. And it is more cost effective. An example of the cost savings is that the assembly is only $4.83 more than ordering key 57, which would only include keys 33, 53, 56, and 57.

I hope this answers your question. If I can be of any further assistance, please respond to this thread. Thank you for choosing Sears, we appreciate your business.

Read More
Rachel Morgan -
Sears Technician
June 24, 2013
See more answers
Q:

What's included in part # 30420 Key #55? 113299142 Craftsman Craftsman 10 inch table saw

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Henry -
June 23, 2013
A:

Thank you for choosing Sears Parts Direct. I can certainly understand how frustrating it can be when your table saw is not working correctly. I’d be more than happy to assist in getting the information on what comes with the arbor housing.

http://s.sears.com/is/image/Sears/PD_0009_113_508123?hei=280&wid=280&op_sharpen=1&qlt=100&sid=MMLxexpertmerch  I did attach a photo of what the arbor housing will consist of as well as what it will look like. If you would like to get that arbor housing ordered you can always order on Searspartsdirect.com as well as calling our 1800-4MYHOME. Thank you for choosing Sears Parts Direct.

Read More
Natasha12 -
Sears Technician
June 24, 2013
See more answers
Q:

What steps do I follow to replace the arbor/bearing on my Craftsman table saw model# 113.299142 and what lubricant do I use?

A:

When it comes to replacing the arbor bearing on the Craftsman table saw, it sound like the expert knows how to, in the link provided below. Hope this is helpful while an expert responds to all your questions within two business days.

Read More
Anna T -
January 14, 2013
A:

Thank you for your question.

I am sorry you are having a problem with the saw. If you have remove the belt and the pulley and then the key out of the keyway, then remove the retainer clip and this should allow you to drive the arbor shaft out of the arbor housing. Be careful not to crack the arbor housing or the cradle. If you are having a problem getting the arbor shaft out then I would suggest, if you have not taken the arbor out of the cradle, I would suggest that you do and put the arbor over a firm surface, like a vise and support the arbor housing so you can drive the arbor shaft out of the arbor housing without damaging the arbor housing. The housing parts are cast iron and if you use too much force you can break the housing. It may be that the inner bearing next to the blade may have the bearing race stuck to the arbor shaft and it will require a little more force to remove it. The arbor is attached to the cradle with a keeper ring and a washer. Mark the location of the arbor gear and the worm gear so you can return it to the same location when putting it back after replacing the arbor shaft and bearings. Please let me know how it went and we can continue to troubleshoot with that information.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
January 16, 2013
A:

Hi, Mark T, I followed your instructions and have installed the new arbor shaft. It seems to have corrected the blade wobble. I haven't been able to test it yet because I had a problem replacing the belt pulley. The key didn't match up as smoothly as it did with the old shaft. The slot on the new shaft seems the same size, but the key rides too high in the slot for the pulley to slide on. Do I need to replace the key? If so, how do I determine the correct size? (Thanks for your excellent instructions!)

Read More
Keith -
January 17, 2013
A:

Keith, Getting the key in the right position for the pulley to slide on can be tricky. I recommend tapping down the end of the key closest to the end of the shaft. Then slide the pulley onto the shaft and over the key as far as it will go. Then use a flat blade screwdriver and hammer to tap down the opposite end of the key. This is how I do it. If this does not work, you have to get a new key. You should be able to pick one up at your local hardware store. The size of the key is 3/16" X 3/4" woodruff key.

Read More
Mark T -
Sears Technician
January 20, 2013
A:

Thanks, Mark, your information was extremely helpful. I have successfully replaced the arbor and it seems to have solved the blade wobble.

Read More
Keith -
January 24, 2013
A:

Keith, I am glad to hear you have the saw cutting like new again. If you have any other problems, please keep us in mind. We have experts in all fields. Thank you for using Manage my life.

Read More
Mark T -
Sears Technician
January 28, 2013
See more answers

Top Parts