Model #113243300 CRAFTSMAN Saw Band

  • Unit Breakdown
    3 Results
  • Frame Assembly
    3 Results
  • Leg Set
    3 Results
  • Motor Part
    3 Results
Find part by diagram >

Question and Answers

Q:

I have model 113243300 band saw. what is the length of the blades so I can purchase new ones 113243300 Craftsman 12-inch band saw/sander

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your saw and I do understand your frustration. Glad to help out. I'm looking at your model number 113243300 and the length is 80 inches and the width can be either 1/4 which it originally came with or a blade 1/8 to 1/2 inch can be used as well. The part number for the blade is 60272 (26595). I have included a link to our Parts Direct page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

Read More
Sherman_G_Wallace -
Sears Technician
October 13, 2014
Q:

Bandsaw tire replacement won't stay on.

A:

Band saws are great for projects and making stuff. The tire not staying on the band saw can be very frustrating. I found some information for you that I am hoping will help you. I am adding the link below to help you with your question while you wait for your expert response. It may take your expert 24-48 hours. I do hope that this will help you with the band saw.

Read More
Marc H -
June 05, 2012
A:

I forgot, I would like to suggest adding your model number to better help your expert.

Read More
Marc H -
June 05, 2012
A:

Thanks for the help, my model number is 113.243300

Read More
Chad -
June 05, 2012
A:

Heating the tires may have caused them to stretch out too much and that could be causing this. Typically, the tires are very extremely hard to get on the wheel and often it will require an extra set of hands to get them on. If you're in doubt about the heat being the issue then there is something wrong with the tire. I've never had a problem getting a new tire to stay on once I finally did get it to go on.

I've heard of people using a very thin coat of epoxy to help keep the tires on, but I don't recommend trying it unless you absolutely cannot get the tire to stay on. You really have nothing to lose by trying it as the tire has been heated and cannot be returned because of that. So you may wan to considering trying that.

Thank you for using Manage My Life!

Read More
Wade_B -
Sears Technician
June 06, 2012
A:

Try the Ultra Blue Urethane Tires from this site:www.bandsawparts.com.These tires are made of urethane and doesn't require glue to keep the tire in place and generally lasts longer than a typical rubber tire. But make sure you select the tires that are a couple of inches smaller than the wheel for a good and reliable fit.

Read More
Fabitfast -
June 07, 2012
See more answers
Q:

I got a Band saw (modelno. 113.243300 and having trouble installing the new wheel tires on it.

A:

ManageMyLfe.com is a great place to find your owner's manual and installation guides for appliances. I did some research and found the owner�s manual. I have attached the link below. Your expert will follow up and verify this information shortly. If you are having a specific problem please submit your question on the existing thread by click on the reply box below for your expert.?

Read More
Jackie S -
November 06, 2011
A:

The tires for the band saw are smaller than the wheels to insure they fit tight and don�t walk off the wheels. This makes them difficult to replace.

Place the tires in a container of hot water for 20-30 minutes before installing them. This will make the tires stretch a little easier.

It is best to have 2 people to install the tires. The extra hands can guide the tire onto the wheels and allow you to use 2 hands to rotate the wheel to run the tire on.

Some people use short pieces of 3/8 inch dowel to pry the tire over the edge of the wheel. Don't use a square shaft screwdriver to pry the tire. The edge of the shaft will damage the tire. Be sure the tire is between the 2 lips on the wheel when you are through.

Read More
Jimmy K -
Sears Technician
November 07, 2011
A:

Well I finually got them on the bandsaw. All I got to say to this subject, Is I will supply the bullet and you can shoot the person who thought up this idea for being tight and smaller. I had one hellva hard time doing this repair.

Read More
Donald -
November 07, 2011
A:

Good work Donald. I agree with your sentiment completely. The tires do last a long time, thank goodness. Everyone I have helped with this agrees with you.

Read More
Jimmy K -
Sears Technician
November 07, 2011
See more answers

Top Parts