Model #113232240 CRAFTSMAN Jointer/Planer

  • Table Infeed Assembly
    3 Results
  • Cutter Head Assembly
    3 Results
  • Fence Assembly
    3 Results
  • Panel Assembly
    3 Results
  • Switch And Motor Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

belt replacement for jointer 113232240 Craftsman 6 1/8 inch jointer/planer

A:

Thank you for choosing sears I would be happy to help you with your planer. Upon researching model 113232240; at this time we don’t know of a different belt that would fit your model.

I trust that this information will help you, thank you have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
December 09, 2014
Q:

Craftsman Professional 6 1/8" Jointer / Planer with unknown Model #

A:

I know how useful the owners manual can be since it carries some great troubleshooting tips. While you are waiting for your expert answer, I am adding a link that will help you in finding the model number on most appliances. I am also adding a link in where you can enter your appliance model number and the owners manual will pop up. I hope my links are useful.

Read More
Joseph P. -
August 10, 2011
A:

Thank you for your question on the jointer.

If it is one of the professional series it would be either the 152. Or the 351.

I think it may be the first model of the 152.source jointers we had.

Try model 152.217060, and take a look at this one to see if it looks like yours.

Please let me know if it is correct or not.

Sam A.

Read More
Sam A -
Sears Technician
August 11, 2011
A:

Hi Sam, Not quite, The Base stand on mine is angled similar to a mountain with no peak. the ends / sides are solid at the ends with a slight curvature at the bottom and the front and back have an oval piece cut out of the bottom that is 10 1/2" high, over all height of stand is 27". The whole unit is 38 3/8" high ( including fence Height). When my husband comes home on Wednesday Night he said he would show me how to do photo bucket so I can Link a picture back to this, something I haven't done. The dust collection System is a half bag that hooks on a barrel / garbage can coming off the left hand side, if that helps. Is there any specific place on the planer / jointer that I might have missed seeing the Model / Serial Numbers, usually they have a little plate with all that info but could not find. The Info that I listed above is what is on the front of the Planer / Jointer In first english then french kind of like a great big name plate with all info. I went through all of the manuals one by one listed under planer / jointer on this sight and couldn't find my model. Thanks for your help and knowledge in this matter, Jenifer.

Read More
Jenifer -
August 12, 2011
A:

Thank for the update Jenifer. Know it sounds like it is a 113. model. Do you know about when it was purchased because the 113. manufacturer was ended about 1998. If it was an 113.source it would be in the same area that you were reading from on the front of the jointer. I believe you said it was a Craftsmen Professional and they didn't start unit about 2000. I think once you are able to send me a picture we can figure out the model. Sam A.

Read More
Sam A -
Sears Technician
August 13, 2011
See more answers
Q:

I have a craftsman Model #113232240 jointer and I'm looking for the size on the handwheels part # 824918

A:

When trying to locate parts for your Craftsman it can get a little tough especially if Sears.com website to sell them. While you are waiting on an expert to answer your question, You can visit Sears Parts Direct website to search for the parts you need. I attached the link below. Hope this helps! www.searspartsdirect.com

Read More
Dezeray S -
November 03, 2010
A:

Thank you for your question.

I can understand wanting to replace a broken handle on your jointer.

And you are right the original part is not longer available since the manufacture of that product is no longer in business and the parts stock is depleted.

� I do not have the specifications for that square handle shaft, but what I do have is some replacement handles for other power tools built by that manufacture that may fit.

� There are three different styles of handles.

� The first one is a 3/8 D shaft style with a part number of 62912.

� The second style is a HEX type with a part number of 816499.

� The third style is a � inch round with a part number of 818526.

If any of these styles look like the size you have on your jointer they may fit.

If they are not the right size for you jointer you may have to fashion one yourself.

I do not know of any after market manufactures of these handles.

Sometimes you can do a query online and there may be a person that may have one they are willing to sell. A lot of these jointers were sold, and there are people that acquire these units from garage sales, and then will part them out.

I am sorry that I could not be of more help.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
November 03, 2010
See more answers

Top Parts