Model #113232211 CRAFTSMAN Jointer/Planer

  • Jointer Assembly
    3 Results
  • Fence Assembly
    3 Results
  • Table Assembly
    3 Results
  • Cutter Assembly
    3 Results
  • Switch Assembly
    3 Results
  • Leg Set Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

New Jointer motor needed for 113.232211 113232212 Craftsman Jointer-planer

A:

Thanks for using SearsPartsDirect.com, and for being a valued member. 

Unfortunately, that motor has since been discontinued with no direct substitute offered by the manufacturer. The only foreseeable option would be to visit an electrical supply and try to match one up as closely as possible to the original based upon design and spec. As with any aftermarket motor replacement, there will more than likely be fabrication involved in getting it to mount and work properly. I don’t see any new old stock motors with that part number still in circulation online, so an aftermarket will be your only option.

I hope this helps, and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
October 07, 2014
Q:

sears/craftsman jointer model #133-232211 blade not spinning.

A:

Thank you for your question.

 

I am sorry you are having a problem with the jointer. Based on what you have stated I suspect the cutter head turns freely. If it turns freely the motor is not binding. If the motor just hums when you turn the switch on the problem could be a defective motor relay, motor capacitor, or motor. About the only way to diagnose, the unit is to use a voltmeter. If you have a voltmeter and feel confident checking live voltage I will be happy to assist you with diagnosing the problem. First, unplug the unit from the outlet. Then remove the two screws located on the front by the switch. Be sure to reach under the jointer and hold the plastic electrical box in place while you remove the screws. The relay fits into the box a particular way and I do not want it to fall out and you not know how it fits. Once the screws are removed, pull the box away and note how the parts fit into the box. Then pull the relay out of the box and position it with the top up. Once positioned connect the meter leads to the red wire on the relay and the other on the white wire. You will need to push the lead into the wire nut securing the white wires. Once the leads are connected and cannot touch anything metal, plug the jointer in and turn it on. If you do not have a reading of 120 volts, the relay is defective. If you have the 120 volts, move the lead from the red wire to the black wire on the relay and turn it on. If you have 120 volts, the relay is fine. If this is the case, unplug the unit and remove the capacitor. The capacitor has a rating on the side. If your meter has a microfarad setting, you can check the capacitor by placing the leads on the terminals. If it is not close to the rating printed on the side of the capacitor, the capacitor is defective.

 

Once you determine the problem, the parts for the jointer can be ordered from the following link. Replacement parts for a Craftsman jointer model 113232211.

I hope this is helpful. Please let me know if you need further assistance.

 

Thank you for using Manage my life.

Mark. 

Read More
Mark T -
Sears Technician
August 29, 2013
Q:

Where can I get an owner's manual for a Craftsman jointer planer?

A:

I know how helpful it is to have the manual for your jointer/planer. I was able to find the manual for your model. I attached the link below. I hope this helps.

Read More
Jackie S -
June 15, 2012
A:

Thank you for submitting your question. I was unable to find the owner's manual for your planer for online viewing. However, I did find the manual available for purchase on our Sears Parts Direct web site. The manual is part number SP5590 priced at $10.49. I hope this helps. Thank you for choosing Manage My Life.

Read More
Tykara -
Sears Technician
June 16, 2012
See more answers

Top Parts