Model #113197601 CRAFTSMAN Saw Radial

  • Unit
    3 Results
  • Yoke Assembly
    3 Results
  • Base Assembly
    3 Results
  • Arm Assembly
    3 Results
  • Guard Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

how old is this model of saw. 11319760.1 113197601 Craftsman Craftsman 10 inch radial saw

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with your radial saw. Upon researching model 11319760.1; this unit is a 1979.

Thank you for choosing Sears. We appreciate your business. Have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
December 31, 2014
Q:

Have taken off motor but to reconnect black red & brown wires connect to what

A:

the machine is radial arm saw 113.197601 sorry I didn't put in title as I was on manual page

Read More
Doug Liot -
September 18, 2012
A:

That's a pretty good diagram you drew up. Give us a day or two to investigate the proper wiring schedule for you. Would you give us a little more information about the motor itself and how it's used? We'll get back to shortly. Until then, have a nice morning.

Read More
Henry -
September 18, 2012
A:

Thank you for your question on the wire hookup of the motor.

All my diagrams are listed by the model number of the tool.

I show this motor number belonging to an 113.197XXX or an 113.199XXX Radial arm saw.

If the diagram I am sending you does not help then please send me your radial arms saws model number so I can help you further.

The only brown wire I see on the diagram is on the dual voltage side on the bottom of the diagram. If your model is operating on 120 volts then use the top half of the diagram.

I hope this information will help.

Sam A.

Read More
Sam A -
Sears Technician
September 19, 2012
A:

Hi Sam,Yes it is from the 10" Craftsman radial arm saw Model 113.197601 c Serial 2004.M0011 bought in early 1980's . Motor is Motor Srvice #63608 odel C48BP 113 class B, E22922 120 volts 11.5 amp 1 ph MFG No.482 7. The brown wire could be white and really faded. The connector block as shown in photo has a coil in it .I am having a tough time interpreting the symbols on diagram to my connector block. The photos may help. What happens if I connect it wrong?

Read More
Doug Liot -
September 19, 2012
A:

Thank you for the update on the wiring in the radial arm saw arm. You have a capacitor and a hot wire relay up in the arm. I will send you a wiring diagram for the cap and relay. You will see on the diagram that the red wire go on the capacitor and the brown or tan in this case goes onto the start relay onto terminal 4 or on some models 5 which is that upper right connection. I hope this diagram will help you. Sam A.

Read More
Sam A -
Sears Technician
September 21, 2012
A:

Hi Sam Thank you very much for the diagram. It gave me the confidence to wire up the radial arm saw. I started with the tan/white on terminal 4 and it popped the fuse , so it went on terminal 5 at the top and it works fine thanks again for the help.

Read More
Doug Liot -
September 23, 2012
See more answers
Q:

radial arm saw model#113197601 parts that attach saw to table are missing unable to be be purchased through sears

A:

Getting the parts to the Craftsman radial arm saw can be difficult when the saw is over 10 years old. The expert can research these parts for you. It is important to submit the part numbers you are requesting to get the best possible answer. Just click on reply to continue the thread. Have you tried thru sears.com? I am attaching a link to the website.

Read More
Anna T -
July 11, 2012
A: