Model #11097282100 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore residential gas dryer burner not operating

A:

It sounds like you are determined to get the Kenmore dryer working, just like managemylife.com is determined to help you. For the detailed information you are seeking, it may take the expert a few days, at most, to respond. Thanks for your patience.

Read More
Anna T -
January 28, 2013
A:

How will I be notified that the technical expert has responded?

Read More
Remel -
January 28, 2013
A:

Hi,

Thank you for asking this question and allow me to answer it this way.

Voltage comes from the timer to the hi-limit thermostat, to the operating thermostat, to the thermal fuse to the gas valve and igniter. The neutral path is off the vas valve to the motor where 5M and 6M is closed to complete the neutral circuit.
The flame sensor needs to be closed for the igniter to glow. You can measure the blue wire at the thermal fuse and the blue wire at the gas valve to the black wire off the motor. When the motor is running the reading should be some voltage but not 120 volts AC.

I hope this answer is useful and that it helps you correct the problem with your appliance.
Thank you for using ManageMyLife.

Read More
Bill__W -
Sears Technician
January 29, 2013
A:

In case the diagram is too small, Here it is once more.

Read More
Bill__W -
Sears Technician
January 29, 2013
A:

Bill, The diagram you gave me is good. It is almost identical to the one pasted on the inside of the dryer. Maybe my question was not clear. What I need to know or determine is the integrity of the switch. I followed the diagram on the inside of the dryer and made the assumption that the neutral wire was the one that was been manipulated by the various switches before the ignitor unit and the gas valves were activated. I do not wish to replace the switch for $78.00 when it may not be the problem. I would have gotten back to you sooner; but, this is my first time and I did not know how to join back in the conversation. It is really simple; but, I had tried from ManageMyLife.com and I could not even find my question. Thanks, Remel

Read More
Remel -
January 29, 2013
A:

Bill, Does it make sense to connect the blue wire on the door switch to the black wire on the ignitor to determine if the switch is defective? I have not looked at the unit. Since the two wiring diagrams (yours and the one on the dryer) seem to be almost identical, I am assuming that the connection I suggested would tell me if the switch is defective. It is my assumption that when the motor is running that the 6M wire is closed. On my diagram it shows a dotted line to another switch where 1M is closed. Since I don't know the mechanics of he switch, I am reluctant to close the circuit that I suggested. Thanks again, Remel

Read More
Remel -
January 29, 2013
A:

Bill, By the way the second schematic is much clearer than the first one that you sent. Thanks again. Remel

Read More
Remel -
January 29, 2013
A:

The switch you are refering to in the motor switch if so check at the console when the motor is running at the push to start switch the black there to the white or the white and red the voltage should read 0 Volts AC. Confirm the voltage to the valve by reading blue to black at the valve confirm the radiant sensor 0 Volts AC or 120?

Read More
Bill__W -
Sears Technician
January 29, 2013
A:

Bill, OK. I will get back to you some time later once I check into it further. Remel

Read More
Remel -
January 29, 2013
A:

Bill, I am unable to confirm any voltage to the radiant sensor. I also tried the following with no luck whatsoever in getting the ignitor unit or gas valve to work. I closed 5M and 6M circuit as shown on the schematic that you sent me. I also closed the 1M and 2M circuit that was show on the schematic taped to the inside of the dryer. This circuit, 1M - 2M were not shown on your schematic. In any event, the motor runs; but, nothing happens with the ignitor unit or the gas valve. It may be that the motor switch is defective. I thought closing the circuits manually would cause the ignitor unit and the gas valve to function. No such luck at this time. Thanks, Remel

Read More
Remel -
January 31, 2013
See more answers
Q:

belt diagram for kenmore dryer 11097282100

A:

Good afternoon.... I can fully appreciate your need for instructions on that belt. I provided a link below that is to a model number very similar to yours. I will forward your question to an expert will will investigate the matter further. They should send you this information within a day or two. I hope this helps and have a nice day

Read More
Henry -
November 26, 2012
A:

Thank you for your question.

I am sorry you are having a problem installing the belt. I posted an image below showing how the belt should be routed. Just click on the image to enlarge it.

I hope this is helpful. Please let me know if you need further assistance.

Thank you for using Manage my life. Mark

Read More
Mark T -
Sears Technician
November 27, 2012
See more answers
Q:

Dryer stopped working 97282100

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina -
November 01, 2012
A:

Thanks for the question about your dryer that stopped, I will be glad to assist. Model # 110.97282100
Based on the description of failure, I believe that you drive belt has broken. The belt can be replaced by lifting the top, removing a couple screws just inside the cabinet at top and loosening a couple more screws (at cabinet side) below the door frame. Once you have removed the front the drum comes out to access the motor and idler pulley the belt attaches to. I will attach a link to the belt here; Drive Belt The belt comes with installation instructions.

I would also suggest you check the condition of the idler pulley and replace if worn.
I hope this helps, should you need additional assistance reply with more details and I will be happy to respond.

Read More
Ron H -
Sears Technician
November 02, 2012
See more answers

Top Parts