Model #11097088601 KENMORE ELITE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • 8576353 Burner Assembly
    3 Results
  • Door Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers


My dryer wont start, sensong revising time light is on. 11097088601 Kenmore Elite Dryer


Thank You for choosing Sears and being a valued member. It is unfortunate to hear that you are having issues with your dryer and I do understand your frustration. Glad to help out. I'm looking at your model number 11097088601 and this is not going to be an easy problem to deal with. It sounds like the door switch and this is where the checks need to start. You will need to make voltage check and use a multimeter in making the checks. The gas will need to be turned off and the console will need to be raised. The initial checks can be at the board, checking power and the relay to the motor and the door switch. I have numbered the checks in the order that needs to be done. 1. Check the power the neutral. 120 volts AC is what to expect. 2. Select a timed dry cycle and start the dryer and check the power to the motor to neutral, expect 120 volts AC. 3. Check the door to neutral if the is 120 volts AC you have a faulty door switch or open in the harness. If you cannot select the various cycles and options then the problem might be a stuck or shorted keypad. First check the cycle signal button will lock or unlock the control. If the unit is in control lock then none of the cycles or options will work. If the control lock is not turned on then likely the problem is a stuck or shorted keypad. I also recommend checking the moisture sensors item 34 for any lint or any type of buildup. Here is a link that may help with additional troubleshooting. I have included a link to our Parts Direct page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page. I trust this information will help you.


Thank you for choosing Sears


SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
January 14, 2015

door swap question 11097088601 Kenmore Elite Dryer



Thank you for choosing Sears Parts Direct. I can certainly understand how you would want to know if you can reverse the doors on your washer and dryer. In order to check if you are able to swap the doors we will need the model numbers off of the washer and dryer itself. The model numbers are usually located near the door or on the door on an industrial sticker. They usually start with three digits followed by a decimal and more numbers. Once you have the model number I will be able to check if the doors are reversible.

Thank you for your question. Have a great day.

Read More
Natasha12 -
Sears Technician
November 08, 2013

Dryer HE5 stops heating after 10 minutes or so. 110.97088601


Hello glad to help.  Thank You for choosing Sears

I am sorry and do understand your frustration when the dryer isn't heating. 

Glad to help out.   Im  looking at your Kenmore model number 110.97088601

I am looking at the Faut/Error codes for this model of F:01


F:01 flashes when there is a primary control failure.

Replace the machine control electronics. 

Replacing the controls says to Unplug the machine for safety  and or disconnect the power.

Remove the 3 rear screws from top panel, slide the top panel to rhe rear to remove.

Next remove the 2 screws that hold the machine control electronics bracket in place. 

Slide the bracket over the top of the drum to access the machine contorl board connectors.

Remove all wire connections to the control board.

Remove the screw holding the machine control board from the mounting bracket.

This is directly from the service manual on the F01 code. Below is the part number and if you decide to buy, I would suggest calling us directly at 1-800-366-7278 and speak to our Sears Parts.  Ask them being the price is hight to do a "price match" for you.   They may be able to save you a little to a lot of money.   Worth a shot anyway.

One thing for you to check out on the burner, what I would check out is the coils.  There are 2 coils that are on the burner valve and when they go bad he glow goes off. If I didn't get the F01 code from you, that is what I would tell you to check.

Electronic control board for model 110.97088601

2 coils for burner per model 110.97088601

 If you have further questions please let me know.

Thanks for choosing Sears


Read More
Larry L -
Sears Technician
October 01, 2013

Top Parts