Model #11096350100 KENMORE Residential Dryer

  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • Top And Console
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Need the cubic feet of my kenmore dryer 29" model # 110.96350100 and washer model# 110.91250100

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina F. -
November 11, 2011
A:

Thanks for contacting ManageMyLife.com. Due to the age of the dryer the specs are not available. Below I have included instructions on how to calculate cubic feet in your dryer.

  1. Measure the depth of the dryer from the starting from the back of the dryer to the door opening.
  2. Then measure the diameter of the dryer.
  3. Next you divide the diameter by two to find the radius. Example, if the diameter is three feet, the radius is 1.5 feet.
  4. Last you would calculate the size of the dryer by squaring the radius and multiplying by the depth. Example, if the radius is 1.5 feet and the depth is two feet, the volume is 4.5 cubic feet (1.5 x 1.5 x 2).

I hope this helps!

Thank you for using ManageMyLife.com.

Read More
Jonathan B -
Sears Technician
November 11, 2011
See more answers
Q:

Kenmore Dryer Model Number 110.96350100

A:

I'm sorry to hear that you are having some difficulties with your Kenmore Dryer. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below.

Read More
James -
October 19, 2011
A:

Thank you for your question and I understand your concern.

The first thing that should be checked and confirmed is the voltage supply. The dryer must have 220 volts in order to run and heat. The voltage should be checked and verified at the back of the dryer where the power cord is attached. The voltage must measure 220 volts when measuring across the two outside terminals. NOTE: I do not recommend checking voltage unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician to diagnose and repair your dryer. If you haven't checked and reset the two house circuit breakers dedicated for the dryer; locate the two breakers and reset both breakers by flipping them OFF and ON 2-3 times and then check the dryer for heat.

If it continues to run and not heat; I added an image below of the wiring diagram and an image of the bulkhead to reference. I drew circles around the components that will need to be disconnected and tested for continuity with an Ohm meter. The first component to disconnect and test is the thermal fuse (key#16). I added a YouTube video showing how to test the thermal fuse and how to access and replace the thermal fuse.

NOTE: Disconnect the power cord from the power source before removing the rear panel.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
October 19, 2011
See more answers
Q:

What is wrong with my Kenmore dryer model 110.96350100?

A:

The component that you are apparently describing is the thermal fuse. This is a non-resettable fuse that would prevent the dryer motor from running. The wiring diagram for your dryer is shown in the image below.

Replacing this component will likely fix your dryer problem. You can verify that the dryer will run by unplugging the dryer and taping the blue wires that go to this fuse together with electrical tape. Reassemble and test the dryer. If the motor runs properly then replacing this fuse will fix your dryer. NOTE: Do not leave this fuse bypassed. It is an important safety feature of the dryer that must be replaced.

As an electrician, I am sure that you know that you should unplug the dryer before accessing internal components.

Also, be sure that you check the exhaust vent duct system of the dryer for a clog or restriction. An unresolved restriction in the exhaust air flow of the dryer could cause the fuse to blow again shortly after it is replaced.

You can order parts for the dryer from the Sears PartsDirect website. The part number for the thermal fuse is 3392519.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
March 22, 2010

Top Parts