Model #11096060100 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

kenmore dryer stopped heating!

A:

It can be very aggravating when your dryer fails to heat properly. I did some research and provided a link to a similar question and answer on our site. I hope this will shed a little more light on the issue until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
March 28, 2013
A:

Thanks for the inquiry about your dryer model 11096060100, I will be glad to assist you with the issue. The first thing to verify is having correct power supplied to the dryer, because you dryer is electric heat there could be a breaker tripped and the dryer will still run just not heat so check that first. If breakers are okay then check voltage at terminal block where power cord connects to dryer. You should have 240 volts ac between the two hot lines. (You will need a good volt/ohms meter to test the power and other possible circuit issues.)If power is okay to dryer you will now need to check the Heater and thermostats and the thermal fuse which are located on the back side of the dryer. I will attach an image with the wiring diagram so you can trace the circuit and test each component. The previous issue with a no-heat on one cycle would be a timer issue.  _Always disconnect power supply before servicing the appliance and when testing live voltage be sure to wear proper safety equipment (gloves and eye protection) also be aware of sharp metals on product_If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.Ron H.

Read More
Ron H -
Sears Technician
March 29, 2013
A:

Ron, where do I find the attached image with the wiring diagram that you've sent to me?

Read More
rick300zx -
March 29, 2013
A:

Hi Rick Try clicking on this link: Dryer Repair RonH.

Read More
Ron H -
Sears Technician
March 29, 2013
See more answers
Q:

Dropped in lint trap 11096060100 Kenmore Electric dryer

A:

I understand that you dropped something in your lint trap and you want remove it. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina -
March 07, 2013
A:

Alina, where are the attachments?

Read More
Kortni -
March 07, 2013
A:

Items going down the lint screen is a comon occurance.  You will need to remove the back panel to access, the lint chute assembly. 

First disconnect the electrical power to the dryer. Pull out the lint screen & remove the 2 screws going through the top panel. Pull the dryer out & remove the rear panel. Be careful of the sharp metal edges. Remove the screws securing the lint screen chute assembly to the bulkhead. Use the image below as a guide. Lift the top panel up by pulling it forward enough to clear the front locking clips. Remove the 2 screws securing the rear bulkhead to the right & left side panels. You should now be able to separate the lint chute assembly far enough from the rear bulkhead to reach the bolt. Reassemble in reverse order.Please advise if further help is needed.  Thank you for using Manage My Life.

Read More
Barbara H. -
Sears Technician
March 08, 2013
See more answers
Q:

Dryer will buzz if I hold the button down, but will not spin 11096060100 Kenmore Electric dryer

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina -
February 09, 2013
A:

Having the back off would help if the dryer was not heating but for the proble you describe you'll have to remove the front panel to access the motor, belt and pulleys.  The image below will show how to raise the top and remove the front panel.  Unplug the dryer first.  First thing to try is to get a little help and while you  push the start button have the helping hand open the door, hold the door switch in and give the drum a little push start.  The dryer may start with a little help.  You can also note how easilly the drum rotates when turned.  Hard to turn might indicate the belt is off the idler pulley or a problem with the drum rollers.  I hope this helps.  You can reply with any additional details for further assistance. 

Read More
Fred M -
Sears Technician
February 09, 2013
See more answers

Top Parts