Model #11095872402 KENMORE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • 8576353 Burner Assembly
    3 Results
  • Door Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

DRYER NOT HEATING 11095872402 Kenmore Residential dryer

A:

I mean it is a GAS dryer. Gas line is one. Dryer vent system is clear.

Read More
Tosha -
March 16, 2014
A:

Thank You for contacting SearsPartsDirect.com. I do apologize for the delay in answering your question.

There could one of several possible failures preventing your dryer from heating.

Control Panel

Control thermostat

High limit thermostat

Flame sensor

Solenoid coils

Glow bar igniter

Motor centrifugal switch

Loose wire connection

I recommend calling a service technician to diagnose and repair your dryer. 

Read More
Desirea -
Sears Technician
March 30, 2014
See more answers
Q:

kenmore he4 electric dryer he4 makes click sound when start button is pushed but dryer does not turn on

A:

The sound of only a click when there is wet laundry is a terrible feeling. I located a previous expert answer that may get you on the way to dry laundry while you wait for your expert. If you can add the model number of your dryer it may help the expert provide a better answer.

Read More
Barbara H. -
June 10, 2011
A:

I will need a few more details to help you with this problem.

If you press the start button and it beeps three times then the problem is likely with the thermal fuse, belt switch or door switch.

You will need a meter to check these parts.

Replay with a few more details about if there are lights and if you can program all cycles and options for further assistance.

The image below will help you access the thermal fuse and door switch. Remember to unplug the dryer first.

Read More
Fred M -
Sears Technician
June 12, 2011
A:

Fred I am having a similiar problem with my Kenmore elite HE4 gas dryer #11095872402. I shut the door press the start button and all I hear are 3 beeps and the digital timer flashes on and off but nothing statrs. Could this be the door switch? paul

Read More
Paul -
August 05, 2011
A:

The door switch would be the first thing to check. It can be checked for continuity or it can be bypassed by joining the two wires together. Be sure to unplug the dryer first.

Read More
Fred M -
Sears Technician
August 06, 2011
A:

I had similar problem with my Kenmore Elite HE4 electric Dryer Model 11085861400. Push start button, faint click, lights come on then nothing. I do not have a meter so I removed the thermal fuse and joined the two wires together wrapping them with electric tape. Plugged back in, turned on and yah it worked. Unplugged and bought new fuse for $15.27. Installed and am now drying a load! Thanks to Fred M. for his suggestions!

Read More
Repairmanjim -
September 17, 2012
A:

Good job. When most electric dryers will not run the thermal fuse is a good place to start checking.

Read More
Fred M -
Sears Technician
September 18, 2012
See more answers
Q:

kenmore elite dryer spec sheet

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina F. -
December 15, 2011
A:

The vent is 4 inches in diameter and is located in the center of the rear panel approximately 12 inches from the side of the unit. The center of the 4 inch vent pipe would be 13 1/2 inches from the side.

The height of the center of the vent hole would vary depending on the leveling legs.

The dryer can also be vented out the sides or bottom.

Read More
Fred M -
Sears Technician
December 17, 2011
See more answers

Top Parts