Model #11092593220 KENMORE Residential Washers

  • Control Panel
    3 Results
  • Top And Cabinet
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Miscellaneous
    3 Results
  • Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Dispenser
    3 Results
  • Water System
    3 Results
  • Wiring Harness
    3 Results
  • Gearcase
    3 Results
  • Brake And Drive Tube
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Why my washer won�t rince nor spin

A:

Without a washer or dryer your laundry situation can get quite messy. So I understand your concern. While your waiting for an expert to respond I attached a couple links that might help. I hope these links are helpful!

Read More
Jackie S -
August 14, 2011
A:

Thank you for your question.

By what you have stated, it sounds like a lid switch failure. The lid switch has to be closed for the drain and spin cycle on your washer to work. If the lid switch is faulty, it will fill and wash but nothing else. A quick check you can do is to jump the lid switch and see if it will drain. If the washer operates, the lid switch needs to be replaced.

To jump the lid switch you need to unplug the washer and open the console. I have provided you with the instructions for opening the console below. Once you have the console open, locate the connector for the lid switch. Place an insulated jumper between the two colored wires. Not the green it is a ground and will cause a short. After inserting the jumper make sure it will not touch anything metal, plug the washer in. Start the washer in a drain cycle. If the washer drains and spins, you need to replace the lid switch. Do not leave the jumper in while you are waiting for the part. The jumper is only of the test.

To you replace the lid switch you have to remove the cabinet of the washer. The instructions for that are also in the image below. Once the cabinet is removed you can take the screws out securing the lid switch and remove the harness from the clips along the underside of the cabinet. Then reinstall the lid switch in the reverse order. Before you reassemble the cabinet, please read the instructions for installing the cabinet provided in the image.

Please click here to watch a video on how to replace the lid switch.

I hope this is helpful. Please reply below if you need further assistance. Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
August 16, 2011
See more answers
Q:

I have a Kenmore washer # 110.92593220. Do I need to remove the top to replace the lid switch?

A:

On this particular washer the cabinet/top most be removed to access the lid switch. The image below will help with this.

From the description you give it may be the problem is with the lid strike. This is the part on the lid the activates the switch when the lid is closed. It performs the job of the screwdriver.

The lid switch activator 350733 is available from the following site: Sears PartsDirect .

I hope this information is helpful to you but submit another question with any additional detail for further assistance.

Read More
Fred M -
Sears Technician
April 20, 2010
Q:

Agitator Assembly on a washing machine makes noise

A:

If you pry of the agitator cap to your washer with a flat head screw driver, you will see a screw and washer. Make sure that is tightened properly. You can take that screw off to see the agitator dogs (clutch) underneath. Check for visible damage to the assembly.

Read More
Alyse C. - Personal Solutions Manager -
Sears Technician
January 11, 2010

Top Parts