Model #11092591200 KENMORE Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Miscellaneous Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Brake, Clutch, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Water System Parts
    3 Results
  • Brake And Drive Parts
    3 Results
  • Gearcase Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Do I need the whole agitator assembly if the augur is not pulling clothes down?

A:

You will not need the complete assembly, just the agitate clutches (key#5). The upper agitate auger (key#6) is driven by the agitator clutch (key#5). The agitator clutch are designed to ratchet the augur in one direction when there enough friction upon the auger to push the clothing down. The agitate clutch will wear with use and will need to be replaced. The part# of the agitate clutch is 80040.

Read More
Joey S -
Sears Technician
July 17, 2009
A:

How do I get the auger off so that it can be replaced?

Read More
Willie -
July 12, 2014
See more answers
Q:

Rinse cycle water VERY slow to fill 11092591200 Kenmore Washer

A:

Thank you for choosing SearsPartsDirect. I can certainly understand how frustrating it can be when your washer fills slowly on the rinse cycle. I did look into the model number you have provided and I have found information to assist you. 

I recommend checking the hoses and screens for clogs or debris blocking the water from entering machine. 

It sounds to me like it could be the temperature inlet sensor. 
Click here to view the sensor. 

The sensor is like a thermistor that changes with temperature. 

Remove the cold water hose from the washer after shutting the cold water faucet off, and see how well the water flows out when you turn it back on. You can let the water pour right into the washer's tub. If the water flow is still slow, check for a partially restricted filter screen in the end of the fill hose at the faucet end of hose. Check your fill hose for being pinched or crimped and check the water faucet valve itself for being only partially open or restricted.

I have also found a video that may assist you. Click here to view. 

There could be two parts the inlet valve itself or the temperature sensor. 

 
You can also visit searpartsdirect.com for parts, diagrams, and repair information.
 
 
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
June 12, 2014
Q:

washing machine repair

A:

I can understand your concern over whether or not to remove the tab located on the agitator of your washer. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
October 19, 2012
A:

I believe I can help answer your question but just to be sure please reply with a model number for the best answer.

Read More
Fred M -
Sears Technician
October 20, 2012
A:

The washer model is a Kenmore Ultra Care II and the model number is 110.92591200. Since I posted my question I was in contact with a Sears sub-contracted repair man who suggested I not remove the tabs despite what the repair kit instructions stated. I also subsequently discovered the second tab was still there but was pushed down. I pulled it up to its oiginal position and reconnected the cam to both tabs and the rest of the auger components to the agitator. My wife ran a load in the washer today and it seemed to work fine. Would it work better without the tabs? Maybe you can answer that. Thanks in advance.

Read More
John -
October 21, 2012
A:

I can change or alter the instructions to install the parts. The image below may be helpful.

Read More
Fred M -
Sears Technician
October 23, 2012
A:

Thanks for your assistance. I decided to go with the repair kit instructions and remove the tabs. We ran a couple more loads of wash and the machine seems to be working fine.

Read More
John -
October 23, 2012
See more answers

Top Parts