Model #11092581110 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Control Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Miscellaneous
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

When I start a load of laundry the machine just buzzes. 11092581110 Kenmore Washer

A:

Thank you for choosing Sears Parts Direct. I can certainly understand how frustrating it can be when your washer does not work properly. I did look into the model number you have provided and I have found information that will assist you. It sounds to me like your timer is going out and causing the unit to buz. Or it could be the relay on the motor itself. They will need to be tested with a OHM meter to check the continuity of the parts. 
I would recommend checking the timer first becasue it is easy to access. I do apologize, but I am unsure why your unit would start on its own with a mechanical timer, usually that involves a control board, in which, you do not have in your unit. 

Let me know if this helps.


 If you hear a humming sound, check to see that the water is turned on. If the water is on, there is, either a clogged hose, clogged valve or a bad valve.
 If the washer has a mechanical timer (one that you pull out the knob to start it), using the wiring diagram and a multi-meter, determine that the necessary voltage is reaching the timer. If not, check the diagram or trace the wiring from where the power cord comes into the washer to the timer. Look for a bad place in the cord or wiring harness, and check for the presence of a fuse. If the necessary voltage is present, unplug the washer and disconnect the timer connector(s). Make sure and mark where the wires go. Using the timer chart on the wiring diagram, check the points on the time for the proper continuity, and replace if faulty. If the timer is electronic, power to the control and no power out means a bad control board. Always do a power reset on electronically controlled appliances before replacing any parts. 





 
You can also visit searpartsdirect.com for parts, diagrams, and repair information.
 
 
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

Read More
Natasha12 -
Sears Technician
April 09, 2014
Q:

Kenmore Washer (Model 110.92581110) - Final Spin Not Working

A:

Thank you for your question.  I am sorry for the problem with your Kenmore 110.92581110 Top Load Washer.   From the description of the problem I suspect the Timer is at fault.  I was able to bring up a timer chart for a similar model and the Ultra Wash and Normal cycles both should have 2 spin cycles.  There should be a spin before the rinse cycle and afterwards.  This type of problem is usually caused by a bad Timer contact.    I hope this information is helpful to you.  You can reply below with any additional details for further assistance. 

Read More
Fred M -
Sears Technician
November 12, 2013
A:

Note: I am not sure if my first rely went through - Resending again as follows: Thank you for your feedback. I bought the Timer (part#3946471) and I do have the Repair Manual (Part# LIT4314044 Rev. F). In trying to replace the Timer, I did remove the Timer Knob, then the clear (aesthetic?) plastic cover that fits over the Timer Dial (see attached picture). The Manual (page 29) then says to pull out the Timer Dial. My apprehension at this juncture is where on the Timer Dial should I grab onto to pull it out. From what I can see, there is a protruding piece in the center of the Timer Dial that the aesthetic plastic cover fits over. Please advice is this where I should grab to pull out the Timer Dial? Thank you.

Read More
Anonymous -
November 14, 2013
A:

I thought I follow-up on my last reply. When I tried to pull the Timer Dial out, it seemed to be very tightly attached in the slot and I am worry that it could break if I do it the wrong way. On that note, May I know how is the Timer Dial fitted over the slot that it is fitted into? Is it snapped snuggly into the Timer itself? Thank you again

Read More
Anonymous -
November 15, 2013
A:

Removing the timer dial depends on if you have a timer with a metal body or a plastic body. Check the image below and see if it helps.

Read More
Fred M -
Sears Technician
November 17, 2013
See more answers
Q:

top agitator 11092581110 Kenmore Washer

A:


Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is a problem repairing the washing machine. 

Glad to help out.   Im  looking at your Kenmore model number 110.92581110
 
I see you are looking to remove the  cam-driven piece that is the top part of the agitator.   You have have to remove the cap at the top and stick a long screwdriver down into the middle of the agitator and unscrew the piece.   Then the top part should pop right out.   I have a picture of it on the link below.   If you haven't gotten the cam piece, it is on the link below too.  When you order key number 20 then you get all that in the box as an assembly.
 
 
If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com
 
 
 

Read More
Larry L -
Sears Technician
October 08, 2013

Top Parts