Model #11091551210 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Miscellaneous
    3 Results
  • Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Control Panel
    3 Results
  • Wiring Harness
    3 Results
  • Brake And Drive Tube
    3 Results
  • Gearcase
    3 Results
  • Water System
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

110.91551210 Kenmore 70 Series Washer:

A:

The washer not working can be very frustrating. I found some information for you that I am hoping will be able to help you. Please click here: Kenmore Washer Model 110.91551210. Your expert will also help answer your question. It may take two business days. I do hope that everything works out.

Read More
Marc -
March 12, 2013
A:

Thanks for the information about your washer model 110.91551210; sorry you are having a problem.Based on the description I would first recommend checking the motor wire harness, sometimes while changing the coupler the harness connector can get loose. Also check the wiring to the capacitor that is wired in with some motors. _Always disconnect power supply before servicing the appliance and when testing live voltage be sure to wear proper safety equipment (gloves and eye protection) also be aware of sharp metals on product_Next if the wiring seems ok I would suggest removing the motor from its mount and test, if it will run disconnected from the drive train this would indicated a transmission lock up.  I hope these tips help, if you need additional assistance please reply with added details and I will be happy to respond. If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.Ron H.

Read More
Ron H -
Sears Technician
March 13, 2013
See more answers
Q:

My washer leaks from the bottom the moment water is added to tub , is it the gasket that needs to be replaced? kenmore model #11091551210

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina -
February 21, 2013
A:

Thank you Alina, this information I'm sure is good to know and thanks again for looking out , us poor folk have to stick together LOL Geno

Read More
E.Sanchez -
February 21, 2013
A:

Hi,

Thanks for contacting ManageMyLife. I understand how frustrating it is having trouble with your appliance not operating as it should.

If the water is coming from the center of the tub, that would be the center post gasket, It could also be coming from the pressure switch hose or air dome located on the side of the tub.  I would recommend you check the air dome and hose before purchasing the center post gasket.  To replace the gasket the complete tub needs to be dismounted from the base.  If it is the center post gasket and you have luck that would be all you would need.   

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Bill

Read More
Bill__W -
Sears Technician
February 22, 2013
See more answers
Q:

Kenmore washer

A:

Having a properly working washer is very important. The washer not spinning can be very frustrating. I found some information for you that I am really hoping will help you with the washer. I am adding the links below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that this will help you with the washer.

Read More
Marc -
December 17, 2012
A:

I know that it can be very frustrating to have issues with your washer. On this model the motor will not come on until the lid is closed. I recommend checking the lid switch; as you open & close the lid you should hear the click of the lid switch if you listen carefully. If the motor is running & the unit won�t spin or agitate I recommend checking the motor drive coupler; Tilt the front of the washer up a couple of inches & look on the floor with a flashlight, if you see rubber shavings piled up or broken plastic pieces this is a sign that the motor drive coupler has failed. If the unit agitates but wont spin I recommend checking the clutch & drive block. This will require access the inside of the unit. I would suggest that you have a technician diagnose and repair this. If you would like to schedule service, just click on this link: Sears Home Services . I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
December 17, 2012
See more answers

Top Parts